The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal | OFF or ON | OFF: Rear door RH locked
ON: Rear door RH unlocked |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch signal | OFF or ON | OFF: Rear door LH locked
ON: Rear door LH unlocked |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG ("FL Door Lock Pos" is not normal) | B |
| NG ("FR Door Lock Pos" is not normal) | C |
| NG ("RL-Door Lock Pos SW" is not normal) | D |
| NG ("RR-Door Lock Pos SW" is not normal) | E |
A
B
C
D
E
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J30-8 (LSSR) - 4B-13 | Always | Below 1 Ω |
| J30-8 (LSSR) or 4B-13 - Body ground | Always | 10 kΩ or higher |
| J30-7 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-13 - MB-19 (LSFL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-7 (LSSR) - 4B-12 | Always | Below 1 Ω |
| J14-7 (LSSR) or 4B-12 - Body ground | Always | 10 kΩ or higher |
| J14-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-12 - MB-17 (LSFR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K8-6 (LSSR) - 4B-14 | Always | Below 1 Ω |
| K8-6 (LSSR) or 4B-14 - Body ground | Always | 10 kΩ or higher |
| K8-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-14 - MB-5 (LSWL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-6 (LSSR) - H43-17 (LSWR) | Always | Below 1 Ω |
| K3-6 (LSSR) or H43-17 (LSWR) - Body ground | Always | 10 kΩ or higher |
| K3-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG