Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0417748 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the open switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

B506723E14
2.094,1.281 2.406,1.479 0.313,0.198 10 false UL 2.167,1.917 2.479,2.115 0.313,0.198 10 false L 0.865,1.927 1.177,2.125 0.313,0.198 10 false E 2.354,1.281 2.667,1.479 0.313,0.198 10 false 3 2.344,1.917 2.656,2.115 0.313,0.198 10 false 1 0.677,1.927 0.99,2.125 0.313,0.198 10 false 2 4.948,1.281 5.26,1.479 0.313,0.198 10 false 26 0.646,2.417 0.958,2.615 0.313,0.198 10 false W11 4.938,1.938 5.25,2.135 0.313,0.198 10 false 27 5.115,2.51 5.427,2.708 0.313,0.198 10 false M5 5.198,1.281 5.813,1.479 0.615,0.198 10 false TSW5 5.208,1.938 5.823,2.135 0.615,0.198 10 false TSW6 0.635,2.552 3.438,2.927 2.802,0.375 10 false Back Door Opener Switch Assembly 5.115,2.667 6.656,3.156 1.542,0.49 10 false Certification ECU (Smart Key ECU Assembly) 5.604,0.594 6.219,0.792 0.615,0.198 10 false 5V 6.052,1.26 6.667,1.458 0.615,0.198 10 false 5V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the back door lock and unlock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Back door lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (B-DR OPENING OPERATION)

NG

2.READ VALUE USING GTS (B-DR OPENING OPERATION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B-Dr Opening Operation Back door opening operation Long, Twice or OFF Customize setting displayed -
Body Electrical > Entry&Start > Data List
Tester Display
B-Dr Opening Operation
50003 125 4

Result:
Result Proceed to
Customize setting is Long or Twice A
Customize setting is OFF B



A

3.READ VALUE USING GTS (TR/B DOOR UNLOCK SW)

B

3.READ VALUE USING GTS (TR/B DOOR UNLOCK SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly (open switch) ON or OFF ON: Back door opener switch assembly (open switch) pressed
OFF: Back door opener switch assembly (open switch) not pressed
·

Displays whether the back door opener switch assembly (open switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

The GTS display changes correctly in response to the operation of the back door opener switch assembly.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the W11 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-26 (TSW5) - W11-3 (UL) Always Below 1 Ω
M5-26 (TSW5) or W11-3 (UL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY