Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0417794 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.


PROCEDURE

Hide 71015A 1.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.
B566510

Install the rear seat cushion frame sub-assembly RH with the 6 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 71017 2.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

a.

Temporarily install the rear seatback frame sub-assembly RH to the No. 1 seat cushion frame sub-assembly RH as shown in the illustration.

B566508C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V113147

Install in this Direction - -



b.

Temporarily install the 3 bolts (B).


c.

Using a T55 "TORX" socket wrench, temporarily install the 2 bolts (A).


d.

Tighten the 3 bolts (B) while pulling the rear seatback frame sub-assembly RH as shown in the illustration.

B566509C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Using a T55 "TORX" socket wrench, tighten the 2 bolts (A) to install the rear seatback frame sub-assembly RH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72307E 3.INSTALL NO. 2 RECLINING CONTROL LINK SUB-ASSEMBLY RH

a.
B566506

Install the No. 2 reclining control link sub-assembly RH with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72307D 4.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY RH

a.
B566505

Install the No. 1 reclining control link sub-assembly RH with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72704A 5.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Route the rear seat reclining control cable as shown in the illustration and engage the clamp.

B566504


b.

Engage the 12 clamps to install the rear seat reclining control cable.

B566503


Hide 72210G 6.INSTALL REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY RH

a.

Route the rear No. 1 seat track control cable assembly RH as shown in the illustration and engage the 2 clamps.

B566502C02
0,0 0,0 false
V100135

Clamp
V100136

Wire Harness Clamp



b.

Install the rear No. 1 seat track control cable assembly RH with the 2 wire harness clamps.


Hide 7.INSTALL CONNECTOR MALE HOUSING (w/o Seat Heater System)

a.
B571167

w/o Seat Belt Warning System:

i.

Engage the clamp to install the connector male housing.



Hide 82193 8.INSTALL REAR SEAT WIRE RH (w/o Seat Heater System)

a.
B566498

Engage the 10 clamps to install the rear seat wire RH.


Hide 82193 9.INSTALL REAR SEAT WIRE RH (w/ Seat Heater System)

a.
B571166

w/o Seat Belt Warning System:

i.

Engage the 7 clamps to install the rear seat wire RH.



b.
B566500

w/ Seat Belt Warning System:

i.

Engage the 11 clamps to install the rear seat wire RH.



Hide 71691N 10.INSTALL REAR NO. 1 SEAT CUSHION HINGE UPPER COVER RH

a.
B566497C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claw and guide as shown in the illustration to install the rear No. 1 seat cushion hinge upper cover RH.


Hide 71693 11.INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH

a.
B566495C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and 2 guides as shown in the illustration to install the rear seat cushion hinge lower cover RH.


Hide 72551E 12.INSTALL RECLINING HINGE COVER RH

a.
B566493C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 4 claws and clip as shown in the illustration to install the reclining hinge cover RH.


Hide 71833A 13.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

a.
B566491C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover RH.


Hide 71485 14.INSTALL REAR SEAT HINGE COVER

a.
B566489C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws as shown in the illustration to install the rear seat hinge cover.


Hide 71834A 15.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

a.
B566487C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover LH.


Hide 71486C 16.INSTALL REAR SEAT HINGE COVER LH

a.
B566485C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 5 claws and 6 guides as shown in the illustration to install the rear seat hinge cover LH.


Hide 71629A 17.INSTALL REAR SEAT CUSHION HINGE COVER RH

a.
B566483C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides as shown in the illustration to install the rear seat cushion hinge cover RH.


Hide 73350 18.INSTALL REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY

Hide 72597D 19.INSTALL RECLINING REMOTE CONTROL BEZEL RH

a.
B566481

Engage the 2 claws and guide to install the reclining remote control bezel RH.


Hide 87510R 20.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71077S 21.INSTALL SEPARATE TYPE REAR SEATBACK COVER

HINT:

When installing a separate type rear seatback cover, refer to precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B566516

Engage the 6 claws to install the separate type rear seatback cover to the separate type rear seatback pad RH.

NOTICE:

Be careful not to damage the separate type rear seatback cover.



Hide 22.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.

Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.


b.
B566480C01
0,0 0,0 false
V100155

Fastener


Engage the fastener and 3 hooks.


c.
B566477C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration to install the 2 rear seat headrest supports.

HINT:

Use the same procedure for each rear seat headrest support.



Hide 71701B 23.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

a.
B566474C01
1.219,1.927 1.51,1.604 true 2.604,1.719 2.677,1.417 true 1.125,0.521 1.385,0.719 0.26,0.198 10 true *a 1.083,0.854 1.344,1.052 0.26,0.198 10 true *a 1.052,1.219 1.313,1.417 0.26,0.198 10 true *a 1.146,1.948 1.406,2.146 0.26,0.198 10 true *b 2.5,1.708 2.76,1.906 0.26,0.198 10 true *b
*a Clip
*b Cable


Engage the rear seat reclining control cable as shown in the illustration.

NOTICE:

Make sure to route the cable as shown in the illustration.



b.
B566473C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 4 guides as shown in the illustration.


c.
B566471

Engage the 9 clips and 4 claws as shown in the illustration to install the rear seatback board sub-assembly RH.


d.
B566469

Engage the 2 hooks.


e.
B566468C01
0,0 0,0 false
V100155

Fastener


Close the 2 fasteners as shown in the illustration.


Hide 73178A 24.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B566466C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration to install the seat belt anchor cover cap.


Hide 73373 25.INSTALL REAR SEAT SHOULDER BELT COVER

a.
B566464

Engage the 2 guides and 2 claws to install the rear seat shoulder belt cover.


Hide 73350 26.CONNECT REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY

Hide 72996 27.INSTALL REAR SEATBACK COVER RH

a.
B566462C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 6 claws as shown in the illustration to install the rear seatback cover RH.

HINT:

Use the same procedure for each rear seatback cover RH.



b.
B566460

Engage the 2 claws as shown in the illustration.

HINT:

Use the same procedure for each rear seatback cover RH.



Hide 72053E 28.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH

a.
B566454

Connect the rear seat reclining control cable.


b.
B566453C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


c.
B566451

Install the reclining remote control lever sub-assembly RH with the 2 screws.


Hide 72615A 29.INSTALL REAR SEATBACK LOCK STRIKER COVER RH

a.
B566450C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and claw as shown in the illustration to install the rear seatback lock striker cover RH.


Hide 73380A 30.INSTALL REAR SEAT INNER BELT ASSEMBLY

Hide 71828B 31.INSTALL REAR SEAT CUSHION REAR MOULDING RH

a.
B566448C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 6 claws, clip and 6 guides as shown in the illustration to install the rear seat cushion rear moulding RH.


Hide 71485 33.INSTALL REAR SEAT HINGE COVER

a.
B566446C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clip and 3 claws as shown in the illustration to install the rear seat hinge cover.


Hide 87501E 34.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

a.
B566268

Engage the clamp to install the seat heater control sub-assembly RH.


b.

Connect the connector.


Hide 87510P 35.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71075S 36.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

HINT:

When installing a separate type rear seat cushion cover, refer to precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B566513

Engage the 14 claws.

NOTICE:

Be careful not to damage the bench type rear seat cushion cover.



b.
B566511C01
0,0 0,0 false
V100155

Fastener


Engage the 7 fasteners to install the separate type rear seat cushion cover.


Hide 37.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.

Temporarily install the separate type rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly RH.


b.
B566443

Engage the 6 hooks.


c.
B566444C01
0,0 0,0 false
V100155

Fastener


Engage the fastener and 7 hooks.


d.
B566442C02
1.24,1.948 1.542,1.948 true 2.719,1.542 3.042,1.542 true 1,1.563 0.302,0.823 0.302,0.823 1.156,1.042 true 0.323,0.833 1.333,1.573 true 1.552,1.885 1.865,2.083 0.313,0.198 10 true *b 3.052,1.479 3.365,1.677 0.313,0.198 10 true *a 0.115,0.74 0.271,0.979 0.156,0.24 10 true *a
*a Hook
*b Clamp


Engage the 4 hooks and clamp.


e.
B569683

w/ Seat Heater System:

i.

Engage the 2 clamps.


ii.

Connect the 2 connectors.



f.
B566441

Engage the 4 hooks.


g.
B564001

Engage the 2 hooks to install the separate type rear seat cushion cover with pad.


h.
B566440C01
0.906,1.698 1.323,1.281 false 0.771,1.698 1.083,1.854 0.313,0.156 10 true *a
*a Rubber Band
V113147

Install in this Direction


Pass the rear seat inner belt assembly through the rubber band of the separate type rear seat cushion cover as shown in the illustration.


Hide 71825B 38.INSTALL REAR SEAT CUSHION MOULDING RH

a.
B564000C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 5 claws, clip and 14 guides as shown in the illustration to install the rear seat cushion moulding RH.


Hide 72057F 39.INSTALL REAR SEAT NO. 2 LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B567929

Connect the rear No. 1 seat track control cable assembly RH.


b.
B567928

Engage the 2 guides.


c.
B567927

Install the rear seat No. 2 lock control lever sub-assembly RH with the 2 screws.


Hide 72057E 40.INSTALL REAR SEAT NO. 1 LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B567926

Connect the rear seat reclining control cable.


b.
B567925

Engage the 2 guides.


c.
B567924

Install the rear seat No. 1 lock control lever sub-assembly RH with the 2 screws.


Hide 71848C 41.INSTALL SEAT ADJUSTER COVER CAP RH

a.
B567923

Engage the 2 guides and 2 claws to install the seat adjuster cover cap RH.


Hide 72927 42.INSTALL REAR SEAT CUSHION UNDER COVER RH

a.
B566426

Engage the claw, clip and guide to install the rear seat cushion under cover RH.


Hide 72525J 43.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.
B568068C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration to install the reclining adjuster release handle RH.


Hide 71848K 44.INSTALL SEAT ADJUSTER COVER CAP

a.
B566423

Install the 2 seat adjuster cover caps.


Hide 72806D 45.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

a.
B566434C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws as shown in the illustration to install the rear seat center armrest cup holder sub-assembly.


Hide 72839 46.INSTALL REAR SEAT ARMREST HINGE SHIM

a.
B566436C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear seat armrest hinge shim as shown in the illustration.


Hide 72830 47.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.

Engage the guide as shown in the illustration.

B566432C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)
V113149

Install in this Direction (3) - -



b.
B566430

Install the rear seat center armrest assembly with the washer and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72868B 48.INSTALL CENTER ARMREST HINGE COVER

a.
B566429C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides and claw as shown in the illustration to install the center armrest hinge cover.