Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0417850 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

w/o Parking Support Brake System:

Ultrasonic sensor


Initialization of ultrasonic sensor TOYOTA Parking Assist-sensor System (Click here)
w/ Parking Support Brake System:
·

Ultrasonic sensor*

·

Rear bumper assembly*


·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking Assist-sensor System

·

Parking Support Brake System


(Click here)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

w/o Parking Support Brake System:

Ultrasonic sensor


Initialization of ultrasonic sensor TOYOTA Parking Assist-sensor System (Click here)
w/ Parking Support Brake System:
·

Ultrasonic sensor*

·

Rear bumper assembly*


·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking Assist-sensor System

·

Parking Support Brake System


(Click here)

PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 89342A 2.REMOVE REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E432235

Disconnect the connector.


b.
E432236C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E432241

Disconnect the connector.


b.
E432242C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.


Hide 89348S 4.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E432238

Remove the rear center ultrasonic sensor retainer.


Hide 89348R 5.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E432244

Remove the rear corner ultrasonic sensor retainer.


Hide 89305 6.REMOVE ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Remove the ultrasonic sensor cushion set as shown in the illustration.

B549651C02
0,0 0,0 false
V113147

Remove in this Direction - -