Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417921 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the washer fluid level is lower than a certain level, a warning message is displayed on the combination meter assembly.

WIRING DIAGRAM

E367784E26
4.969,2.219 7.156,2.688 2.188,0.469 10 false Combination Meter Assembly 2.146,1.635 4.333,2.104 2.188,0.469 10 false Level Warning Switch Assembly 5.354,0.938 5.969,1.135 0.615,0.198 10 false WLVL 2.531,0.938 3.146,1.135 0.615,0.198 10 false E 3.604,0.938 4.219,1.135 0.615,0.198 10 false S 5.75,0.51 6.365,0.708 0.615,0.198 10 false IG 3.802,0.938 4.417,1.135 0.615,0.198 10 false 1 2.344,0.938 2.958,1.135 0.615,0.198 10 false 2 2.146,1.49 4.333,1.958 2.188,0.469 10 false A3 4.969,2.063 7.156,2.531 2.188,0.469 10 false H21 5.094,0.948 7.146,1.458 2.052,0.51 10 false 17

PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Washer Level Warning Switch Washer fluid level warning switch OFF or ON OFF: Washer fluid level not low
ON: Washer fluid level low
-
Body Electrical > Combination Meter > Data List
Tester Display
Washer Level Warning Switch
50003 409 25
OK:

The GTS display changes correctly in response to the washer fluid level.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT LEVEL WARNING SWITCH ASSEMBLY
2.INSPECT LEVEL WARNING SWITCH ASSEMBLY
a.

Remove the level warning switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER LEVEL WARNING SWITCH>REMOVAL


b.

Inspect the level warning switch assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER LEVEL WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE LEVEL WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-1 (S) - H21-17 (WLVL) Always Below 1 Ω
A3-1 (S) or H21-17 (WLVL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR