The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from |
|---|---|---|---|---|---|
| B2357 | Lost Communication with Wiper Module | Detection condition:
Auxiliary battery voltage is 9.5 V or more Malfunction Status:
Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly Malfunction Time:
10 seconds or more |
·
Windshield wiper relay assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector ·
WIPER relay |
○ | Main body ECU (multiplex network body ECU) |
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Disconnect the A7 windshield wiper relay assembly connector.
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A7-4 (MPX1) - H44-5 (CXP1) | Always | Below 1 Ω |
| A7-4 (MPX1) or H44-5 (CXP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) |
Check for voltage and pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H44-5 (CXP1) - Body ground | Ignition switch ON | Pulse generation |
| Less than approximately 100 seconds after ignition switch turned off | ||
| Approximately 100 seconds or more after ignition switch turned off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Power Relay | Function to operate the IG1 WIP relay | OFF or ON | - |
| Tester Display |
|---|
| Wiper Power Relay |
IG1 WIP relay operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A6 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-3 (E) - Body ground | Always | Below 1 Ω |
| A7-5 (ES) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-8 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Less than approximately 60 seconds after ignition switch turned off | 11 to 14 V | |
| Approximately 60 seconds or more after ignition switch turned off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the WIPER relay.
Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (WIPER relay) - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-8 (+B) - 3 (WIPER relay) | Always | Below 1 Ω |
| A6-8 (+B) or 3 (WIPER relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the WIPER relay.
Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (WIPER relay) - H43-21 (WPS) | Always | Below 1 Ω |
| 2 (WIPER relay) or H43-21 (WPS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WIPER relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG