Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417921 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper Motor Circuit  


DESCRIPTION

This circuit is the power source circuit for the rear wiper motor assembly.

WIRING DIAGRAM

E394654E09
3.25,1.313 3.406,1.51 0.156,0.198 10 false E 3.167,0.396 3.479,0.594 0.313,0.198 10 false +B 3.469,0.385 3.625,0.583 0.156,0.198 10 false 4 3.469,1.313 4.281,1.646 0.813,0.333 10 false 5 3.177,2.125 3.49,2.323 0.313,0.198 10 false LS 4.479,2.115 4.635,2.313 0.156,0.198 10 false 1 3.469,2.115 4.313,2.323 0.844,0.208 10 false 3 4.698,2.115 5.313,2.313 0.615,0.198 10 false RWRY 4.031,0.656 5.26,0.854 1.229,0.198 10 false WIPER RR 5.448,0.49 6.99,0.792 1.542,0.302 10 false from IG1-NO. 2 Relay 4.927,2.885 5.458,3.135 0.531,0.25 10 false H42 4.938,3.063 6.583,3.708 1.646,0.646 10 false Main Body ECU (Multiplex Network Body ECU) 0.938,2.865 2.573,3.063 1.635,0.198 10 false W4 0.948,3.042 4.771,3.24 3.823,0.198 10 false Rear Wiper Motor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Wiper Operation Function to operate the rear wiper motor assembly OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Rear Wiper Operation
50004 123 90
OK:

Rear wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT REAR WIPER MOTOR ASSEMBLY
2.INSPECT REAR WIPER MOTOR ASSEMBLY
a.

Remove the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL


b.

Inspect the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - REAR WIPER MOTOR ASSEMBLY)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - REAR WIPER MOTOR ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W4-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W4-5 (E) - Body Ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W4-3 (LS) - H42-1 (RWRY) Always Below 1 Ω
W4-3 (LS) or H42-1 (RWRY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR