Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417921 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Motor Circuit  


DESCRIPTION

When the windshield washer motor and pump assembly receives signals from the windshield wiper switch assembly, it operates to spray washer fluid from the washer nozzle sub-assemblies.

WIRING DIAGRAM

E394733E09
1.083,0.271 1.698,0.469 0.615,0.198 10 false IGWS 1.083,0.75 1.698,0.948 0.615,0.198 10 false MPX1 1.115,1.188 1.573,1.385 0.458,0.198 10 false +WR 1.167,1.677 1.625,1.875 0.458,0.198 10 false -WR 1.115,2.156 1.573,2.354 0.458,0.198 10 false EWS 1.625,2.167 1.938,2.365 0.313,0.198 10 false A6 1.625,0.292 1.938,0.49 0.313,0.198 10 false A6 1.625,1.208 1.938,1.406 0.313,0.198 10 false A6 1.625,1.688 1.938,1.885 0.313,0.198 10 false A6 1.625,0.771 1.938,0.969 0.313,0.198 10 false A7 1.656,0.073 1.813,0.271 0.156,0.198 10 false 6 1.656,0.552 1.813,0.75 0.156,0.198 10 false 4 1.646,0.99 1.802,1.188 0.156,0.198 10 false 1 1.667,1.458 1.823,1.656 0.156,0.198 10 false 7 1.656,1.948 1.813,2.146 0.156,0.198 10 false 5 0.229,2.49 1.729,3.281 1.5,0.792 10 false Windshield Wiper Relay Assembly 2.198,1.563 2.354,1.76 0.156,0.198 10 false 2 2.406,1.563 2.719,1.76 0.313,0.198 10 false SW 3.51,1.573 3.667,1.771 0.156,0.198 10 false B 3.729,1.573 3.885,1.771 0.156,0.198 10 false 1 2.25,1.938 2.563,2.135 0.313,0.198 10 false A38 2.26,2.094 3.885,2.854 1.625,0.76 10 false Windshield Washer Motor and Pump Assembly 5.26,1.104 5.573,1.302 0.313,0.198 10 false H44 5.26,1.26 6.927,2.031 1.667,0.771 10 false Main Body ECU (Multiplex Network Body ECU) 5.375,0.76 5.99,0.958 0.615,0.198 10 false CXP1 5.177,0.594 5.333,0.802 0.156,0.208 10 false 5 3.719,0.271 6.781,0.469 3.063,0.198 10 false from IG1-NO. 2 Relay 2.74,0.417 3.656,0.615 0.917,0.198 10 false WASHER 0.927,3.281 4.75,3.479 3.823,0.198 10 false : CXPI Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Washer Relay Function to operate the windshield washer motor and pump assembly (Front) OFF or ON -
Rear Washer Relay Function to operate the windshield washer motor and pump assembly (Rear) OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Washer Relay
50004 123 77
Body Electrical > Main Body > Active Test
Tester Display
Rear Washer Relay
50004 123 89
OK:

Windshield washer motor and pump assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
a.

Remove the windshield washer motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


b.

Inspect the windshield washer motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPLACE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Disconnect the A6 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-6 (IGWS) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-5 (EWS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (+WR) - A38-1 (B) Always Below 1 Ω
A6-7 (-WR) - A38-2 (SW) Always Below 1 Ω
A6-1 (+WR) or A38-1 (B) - Body ground Always 10 kΩ or higher
A6-7 (-WR) or A38-2 (SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR