Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417921 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.

WIRING DIAGRAM

E394730E20
1.552,0.583 1.865,0.781 0.313,0.198 10 false A6 1.594,0.375 1.75,0.573 0.156,0.198 10 false 4 1.24,0.594 1.552,0.792 0.313,0.198 10 false +2 4.49,0.969 4.802,1.167 0.313,0.198 10 false +S 6.51,1 6.667,1.198 0.156,0.198 10 false E 6.708,1.01 7,1.5 0.292,0.49 10 false 4 4.26,0.49 4.552,0.771 0.292,0.281 10 false 3 4.26,0.99 4.813,1.406 0.552,0.417 10 false 1 1.552,1.104 1.865,1.302 0.313,0.198 10 false A7 1.552,1.573 1.865,1.771 0.313,0.198 10 false A6 1.094,1.115 1.458,1.354 0.365,0.24 10 false +SM 1.24,1.573 1.552,1.771 0.313,0.198 10 false +1 1.583,0.875 1.948,1.115 0.365,0.24 10 false 6 1.583,1.365 1.948,1.604 0.365,0.24 10 false 2 0.135,2.375 1.625,3.135 1.49,0.76 10 false Windshield Wiper Relay Assembly 4.479,0.469 4.792,0.667 0.313,0.198 10 false +2 4.49,1.458 4.802,1.656 0.313,0.198 10 false +1 4.26,1.458 4.813,1.833 0.552,0.375 10 false 5 4.5,2.521 5.802,2.729 1.302,0.208 10 false A37 4.49,2.688 6.677,3.313 2.188,0.625 10 false Windshield Wiper Motor Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON -
Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Lo Operation
50004 123 92
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Hi Operation
50004 123 93
OK:

Windshield wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Remove the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


b.

Inspect the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the A6 and A7 windshield wiper relay assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-2 (+1) - A37-5 (+1) Always Below 1 Ω
A6-4 (+2) - A37-3 (+2) Always Below 1 Ω
A7-6 (+SM) - A37-1 (+S) Always Below 1 Ω
A6-2 (+1) or A37-5 (+1) - Body ground Always 10 kΩ or higher
A6-4 (+2) or A37-3 (+2) - Body ground Always 10 kΩ or higher
A7-6 (+SM) or A37-1 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR