The main body ECU (multiplex network body ECU) controls the headlight cleaner motor and pump assembly.
Check that the front washers are normal before performing the following procedure.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>OPERATION CHECK
Check that the lighting system is normal before performing the following procedure.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the fuses and relays for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check that the low beam headlight operates normally.
Low beam headlight operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL
Inspect the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-2 (B) - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A14 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-1 (L) - A14-6 (PB) | Ignition switch off*1
Always*2 |
Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A14-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A14-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H42 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H42-12 (FWSR) - A14-5 (FRWA) | Ignition switch off*1
Always*2 |
Below 1 Ω |
| H42-12 (FWSR) or A14-5 (FRWA) - Body ground | Ignition switch off*1
Always*2 |
10 kΩ or higher |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-31 - A14-1 (HDLO) | Ignition switch off*1
Always*2 |
Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG