Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418444 CRANKSHAFT POSITION SENSOR A

2GR-FKS ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 11401G 1.INSTALL CRANKSHAFT POSITION SENSOR

a.
A459459C01
1.656,1.594 1.656,1.208 false 3.167,1 2.99,1 false 1.604,1.604 1.917,1.76 0.313,0.156 10 false *a 3.177,0.896 3.427,1.146 0.25,0.25 10 false *b
*a O-ring Groove
*b Crankshaft Position Sensor Tip


Perform this procedure only when reusing the crankshaft position sensor.

i.

Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



ii.

Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.



iii.
A407852C01
0.906,1.344 1.031,1.49 1.031,1.49 1.25,1.49 false 2.219,3.156 2.219,2.865 false 2.521,0.49 2.688,0.26 2.688,0.26 2.896,0.26 false 2.521,1.354 2.688,1.479 2.688,1.479 2.927,1.479 false 2.823,2.875 3.104,2.875 false 1.927,2.26 2.208,2.26 false 2.208,1.49 2.208,1.198 false 0.906,2.99 1.031,3.135 1.031,3.135 1.25,3.135 false 0.865,0.667 1.208,0.51 1.208,0.51 1.406,0.51 true 0.865,2.302 1.208,2.146 1.208,2.146 1.406,2.146 true 1.292,1.417 1.604,1.573 0.313,0.156 10 false *1 2.938,0.177 3.146,0.385 0.208,0.208 10 false *c 0.313,0.333 0.625,0.49 0.313,0.156 10 false *a 0.323,2 0.635,2.156 0.313,0.156 10 false *b 0.583,0.854 0.74,1.052 0.156,0.198 10 true A 1.031,0.854 1.188,1.052 0.156,0.198 10 true A 1.031,2.51 1.188,2.708 0.156,0.198 10 true B 0.604,2.51 0.76,2.708 0.156,0.198 10 true B 2.156,1.51 2.469,1.667 0.313,0.156 10 false *1 2.156,3.177 2.469,3.333 0.313,0.156 10 false *1 2.344,0.094 2.802,0.292 0.458,0.198 10 false A - A 2.354,1.875 2.813,2.073 0.458,0.198 10 false B - B 3.135,2.813 3.344,3.021 0.208,0.208 10 false *c 2.969,1.406 3.177,1.615 0.208,0.208 10 false *c 1.75,2.177 1.958,2.385 0.208,0.208 10 false *c 1.281,3.063 1.594,3.219 0.313,0.156 10 false *1 1.448,0.448 1.656,0.656 0.208,0.208 10 false *c 1.438,2.083 1.646,2.292 0.208,0.208 10 false *c
*1 O-ring
*a OK
*b NG
*c Seam


Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.




b.

Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.


c.

Install the crankshaft position sensor to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the crankshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.




d.

Connect the crankshaft position sensor connector.


Hide 19312 2.INSTALL CRANKSHAFT POSITION SENSOR PROTECTOR

a.

Install the crankshaft position sensor protector to the cylinder block sub-assembly and oil pan sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the hose clamp to the crankshaft position sensor protector with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17150 3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst)