Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM37A0E _51 Engine / Hybrid System _086854 2GR-FKS INTAKE / EXHAUST _0416461 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A370454

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the exhaust manifold assembly LH (TWC: Front Catalyst).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


b.
A454269

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the exhaust manifold assembly RH (TWC: Front Catalyst).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 17173A 2.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.

Install a new exhaust manifold to head gasket (for Bank 2) to the cylinder head sub-assembly.


Hide 17150 3.INSTALL EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold assembly LH (TWC: Front Catalyst) with the 4 nuts.


b.
A454267N01
1.99,0.313 2.146,0.51 0.156,0.198 10 true 1 0.76,1.573 0.917,1.771 0.156,0.198 10 true 2 2.104,1.458 2.26,1.656 0.156,0.198 10 true 3 0.688,0.281 0.844,0.479 0.156,0.198 10 true 4

Tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17119 4.INSTALL NO. 2 MANIFOLD STAY

a.

Temporarily install the No. 2 manifold stay to the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


b.
A454266N01
2.26,0.656 2.417,0.833 0.156,0.177 10 true 1 2.24,1.271 2.396,1.448 0.156,0.177 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 17168 5.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A454265N01
1.302,1.365 1.448,1.542 0.146,0.177 10 true 1 2.979,1.208 3.125,1.385 0.146,0.177 10 true 2 0.354,1.198 0.5,1.375 0.146,0.177 10 true 3

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold assembly LH (TWC: Front Catalyst) with the 3 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 89439D 6.INSTALL NO. 1 SENSOR BRACKET

a.

Install the No. 1 sensor bracket to the cylinder head sub-assembly with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

Hide 11209 8.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 89467C 9.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17173 10.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.

Install a new exhaust manifold to head gasket (for Bank 1) to the cylinder head sub-assembly RH.


Hide 17140 11.INSTALL EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold assembly RH (TWC: Front Catalyst) with the 4 nuts.


b.
A454262N01
2.417,1.219 2.573,1.406 0.156,0.188 10 true 1 1.031,1.938 1.177,2.104 0.146,0.167 10 true 2 2.417,1.906 2.573,2.083 0.156,0.177 10 true 3 1.5,1.01 1.656,1.188 0.156,0.177 10 true 4

Tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.
A454261

Engage the wire harness clamp.


d.

Connect the air fuel ratio sensor (for Bank 1) connector.


Hide 17118 12.INSTALL MANIFOLD STAY

a.

Temporarily install the manifold stay to the exhaust manifold RH (TWC: Front Catalyst) and rear engine mounting bracket with the bolt and nut.


b.
A454260N01
0.76,1.76 0.917,1.938 0.156,0.177 10 true 1 0.469,0.365 0.625,0.542 0.156,0.177 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 37100 13.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the 2 compression springs.

Standard Length 40 mm (1.57 in.)
Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front exhaust pipe assembly.


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipes when connecting them.




d.

Install 2 new gaskets to the front exhaust pipe assembly.


e.

Temporarily install the front exhaust pipe assembly with the 2 bolts, 4 new nuts and 2 compression springs.


f.

Tighten the 4 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


g.

Tighten the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C27
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.708,0.354 1.021,0.656 0.313,0.302 10 false *1 0.74,1.448 0.99,1.698 0.25,0.25 10 false *2 2.875,0.385 3.219,0.677 0.344,0.292 10 false *3 0.625,1.74 1,2.01 0.375,0.271 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



h.
A449083C01
2.833,0.521 3,0.396 3,0.396 2.781,0.917 true 2.344,0.76 2.677,0.76 true 3.042,0.25 3.26,0.5 0.219,0.25 10 true *b 2.115,0.656 2.313,0.927 0.198,0.271 10 true *a
*a Tube
*b Wire Harness Clamp


Connect the heated oxygen sensor (for Bank 2) connector.


i.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


j.
A454812C01
0.76,1.042 1.042,1.198 1.042,1.198 1.063,0.75 true 0.625,0.469 0.813,0.469 0.813,0.469 0.865,0.844 true 0.385,0.375 0.604,0.573 0.219,0.198 10 true *a 0.99,1.219 1.24,1.406 0.25,0.188 10 true *b
*a Tube
*b Wire Harness Clamp


Connect the heated oxygen sensor (for Bank 1) connector.


k.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852B 16.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 17.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH