Home › General › MAINTENANCE › UA80F AUTOMATIC TRANSAXLE FLUID
RM37A0E _V1 General _086848 MAINTENANCE _0418489 UA80F AUTOMATIC TRANSAXLE FLUID A

MAINTENANCE  UA80F AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during automatic transaxle fluid replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 53852B 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 4.REMOVE REAR ENGINE UNDER COVER LH

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 6.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C420751

Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2]


c.
C420752

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3]


d.
C420753C01
2.75,0.917 2.854,0.917 false 2.583,0.813 2.792,1.01 0.208,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4]


e.
C420754

Measure the amount of automatic transaxle fluid drained. [#5]

HINT:

Add the same amount of automatic transaxle fluid in step [#8].



f.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


g.
C420752

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



h.
C420755

Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine ATF WS.

Using automatic transaxle fluid other than the above type may cause abnormal noise or vibration, or damage the transaxle of the vehicle.



i.
C420751

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



j.

Lower the vehicle. [#10]


k.

Start the engine. [#11]


l.

Slowly move the shift lever from P to D, and then back to P. [#12]

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




m.

Allow the engine to idle for 30 seconds to warm it up. [#13]


n.

Turn the ignition switch off. [#14]


o.

Repeat steps [#1] to [#14].


p.

Repeat steps [#1] to [#10].


Hide 7.ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

Hide 8.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

Hide 9.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

Hide 11.PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If approximately 50% or more of the ATF has been replaced during a repair of the transaxle or a similar operation, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION


Hide 53737B 13.INSTALL FRONT FENDER APRON SEAL LH

Hide 51444A 14.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852B 16.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 17.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH