The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
6. SECURE STEERING WHEEL
7.REMOVE FRONT WHEELS
53852B
8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Remove the 4 screws and front wheel opening extension pad LH.
53851D
9.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Remove the 4 screws and front wheel opening extension pad RH.
51441
10.REMOVE NO. 1 ENGINE UNDER COVER
|
Bolt |
|
Screw |
Remove the 3 bolts, 2 clips, 8 screws and No. 1 engine under cover.
51444A
11.REMOVE REAR ENGINE UNDER COVER LH
|
Bolt |
|
Screw |
Remove the bolt, 3 clips, screw and rear engine under cover LH.
51443C
12.REMOVE REAR ENGINE UNDER COVER RH
|
Bolt |
|
Screw |
Remove the bolt, 3 clips, screw and rear engine under cover RH.
58166A
13.REMOVE FRONT FLOOR COVER LH
|
Bolt |
|
Screw |
Remove the 4 bolts, 3 clips, 5 screws and front floor cover LH.
58165C
14.REMOVE FRONT FLOOR COVER RH
|
Bolt |
|
Screw |
Remove the 5 bolts, 3 clips, 3 screws and front floor cover RH.
53737B
15.REMOVE FRONT FENDER APRON SEAL LH
Remove the 2 bolts, clip and front fender apron seal LH from the vehicle body.
53736
16.REMOVE FRONT FENDER APRON SEAL RH
Remove the 2 bolts, clip and front fender apron seal RH from the vehicle body.
52119A
17.REMOVE FRONT BUMPER COVER
18.DRAIN ENGINE COOLANT
19.DRAIN ENGINE OIL
20.DRAIN AUTOMATIC TRANSAXLE FLUID
21.DRAIN TRANSFER OIL
11209
22.REMOVE V-BANK COVER SUB-ASSEMBLY
Hold the rear of the V-bank cover sub-assembly and raise it to disengage the 2 rear clips.
Raise the V-bank cover sub-assembly to disengage the 2 front clips and remove the V-bank cover sub-assembly.
Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.
17750A
23.REMOVE INLET AIR CLEANER ASSEMBLY
Remove the 2 bolts and inlet air cleaner assembly.
24.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
| *1 | No. 1 Fuel Vapor Feed Hose |
| *2 | No. 2 Ventilation Hose |
| *3 | Vacuum Hose Bracket |
Remove the vacuum hose bracket from the air cleaner hose.
Disengage the 2 clamps to disconnect the No. 1 fuel vapor feed hose from the air cleaner hose.
Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose.
Loosen the hose clamp.
| *a | Pin |
Disconnect the mass air flow meter sub-assembly connector.
Disengage the 2 wire harness clamps.
Disconnect the vacuum hose from the air cleaner hose.
Disengage the 3 pins and remove the air cleaner assembly with air cleaner hose.
Make sure the air cleaner support remains attached to the vehicle body.
89661
25.REMOVE ECM
82111
26.DISCONNECT ENGINE ROOM MAIN WIRE
Remove the nut and disconnect the engine wire with engine room main wire from the positive (+) battery terminal.
82121
27.DISCONNECT ENGINE WIRE
Remove the nut and disconnect the engine wire from the negative (-) battery terminal.
28.REMOVE BATTERY
74404B
29.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Disengage the 5 clamps from the battery clamp sub-assembly.
Remove the 3 bolts and battery clamp sub-assembly.
33820B
30.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
| *a | Clip (A) |
| *b | 45° to 60° |
| *c | Clip (B) |
While disengaging the clip (A) as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip (A).
Remove the clip (B) and disconnect the transmission control cable assembly from the transmission control cable bracket.
23826
31.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).
44778
32.DISCONNECT CONNECTOR TO CHECK VALVE HOSE
Slide the clip and disconnect the connector to check valve hose from the brake booster assembly.
16572D
33.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet.
34.SEPARATE RADIATOR HOSE SUB-ASSEMBLY
Slide the clip and disconnect the No. 4 water by-pass hose from the radiator hose sub-assembly.
Slide the clip and disconnect the radiator hose sub-assembly from the water outlet.
Disengage the clamp.
Remove the 2 bolts and separate the radiator hose sub-assembly from the engine assembly.
87245B
35.DISCONNECT INLET HEATER WATER HOSE B
Disengage the 2 clamps.
Slide the clip and disconnect the inlet heater water hose B from the water outlet.
16260
36.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the water by-pass hose assembly from the water hose sub-assembly.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected water hose sub-assembly and water by-pass hose assembly connector with plastic bags to prevent damage and contamination.
23801F
37.DISCONNECT NO. 1 FUEL HOSE
Disengage the 2 claws to remove the No. 2 fuel pipe clamp.
Remove the No. 1 fuel pipe clamp from the fuel tube connector.
Disconnect the No. 1 fuel hose (for Port Injection).
Disconnect the No. 1 fuel hose from the fuel pipe.
Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Disconnect the No. 1 fuel hose (for Direct Injection).
Disconnect the No. 1 fuel hose from the fuel pipe.
Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
88703
38.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
39.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
82121
40.DISCONNECT ENGINE WIRE
After disconnecting the engine wire, secure it with tape or equivalent to keep it out of the way.
Remove the No. 1 relay block cover from the engine room relay block and junction block assembly.
Remove the nut from the engine room relay block and junction block assembly.
Disconnect the 5 connectors from the engine room relay block and junction block assembly.
Disengage the 2 clamps.
Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.
Remove the bolt.
Disengage the 2 clamps and disconnect the engine wire from the vehicle body.
Disengage the 3 clamps.
32943C
41.DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE
Slide the clip and disconnect the No. 3 transmission oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.
Disengage the clamp.
32942
42.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE
Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.
45220
43.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
37100
44.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
45.REMOVE EXHAUST MANIFOLD
46.REMOVE FRONT DRIVE SHAFT ASSEMBLY
11361J
47.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the 2 bolts and flywheel housing under cover.
32101A
48.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
52618
49.REMOVE FRONT BUMPER LOWER ABSORBER
52132A
50.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT
51.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.
Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the front No. 1 engine mounting bracket LH.
Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.
|
Bolt |
|
Nut |
Remove the 2 bolts (A), 2 bolts (B), 4 nuts, front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.
Remove the 4 bolts (C), 2 bolts (D), front suspension member brace rear RH and front suspension member brace raer LH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
52.DISCONNECT VACUUM HOSE
28100
53.REMOVE STARTER ASSEMBLY
35104V
54.SEPARATE BREATHER PLUG HOSE
33197C
55.REMOVE TRANSMISSION BREATHER CLAMP
16260
56.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
57.DISCONNECT HOSE CLAMP
82121
58.REMOVE ENGINE WIRE
Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.
59.INSTALL ENGINE HANGERS
| *A | for Bank 1 |
| *B | for Bank 2 |
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-31121 |
| No. 2 Engine Hanger | 12282-31100 |
| Bolt | 90119-A0117 |
Using an engine sling device and engine lifter, secure the engine assembly with transaxle.
Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
51100G
60.REMOVE FRONT FRAME ASSEMBLY
Remove the bolt and separate the front engine mounting insulator from the front engine mounting bracket.
Remove the bolt and separate the rear engine mounting insulator from the rear engine mounting bracket sub-assembly.
12361A
61.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Remove the 3 nuts and front engine mounting insulator from the front frame assembly.
12371A
62.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the 4 nuts and rear engine mounting insulator from the front frame assembly.
12311A
63.REMOVE FRONT ENGINE MOUNTING BRACKET
30500
64.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
32101
65.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
19315
66.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
67.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
68.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and cylinder head LH.
12305
69.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Disengage the 2 clamps.
Remove the bolt, nut and separate the radiator reserve tank assembly.
Remove the bolt and disconnect the No. 2 earth wire from the engine mounting insulator sub-assembly RH.
Remove the nut, 2 bolts and engine mounting insulator sub-assembly RH from the engine mounting spacer and vehicle body.
12341
70.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
12304
71.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.
Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.
12372A
72.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL