Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Operated Using Any Switch  


DESCRIPTION

If the power back door system cannot be operated using any switch, the multiplex network door ECU may not have been initialized, or there may be a malfunction in the power back door sensor assembly circuit, CAN communication system, back door closer, meter/gauge system, multiplex network door ECU power source circuit, or multiplex network door ECU.

WIRING DIAGRAM

B556200E06
4.063,0.427 4.521,0.625 0.458,0.198 10 false W19 4.063,0.938 4.521,1.135 0.458,0.198 10 false W18 4.052,1.469 4.51,1.667 0.458,0.198 10 false W18 4.177,0.219 4.333,0.417 0.156,0.198 10 false 1 4.479,0.323 4.635,0.521 0.156,0.198 10 false B 4.448,0.833 5.063,1.031 0.615,0.198 10 false ECUB 4.448,1.375 5.063,1.573 0.615,0.198 10 false IG 4.146,0.719 4.458,0.917 0.313,0.198 10 false 20 4.146,1.26 4.458,1.458 0.313,0.198 10 false 18 4.063,2.042 4.521,2.24 0.458,0.198 10 false W18 4.135,1.833 4.448,2.031 0.313,0.198 10 false 26 4.469,1.948 5.083,2.146 0.615,0.198 10 false OSL 4.063,3.552 4.521,3.75 0.458,0.198 10 false W18 4.188,3.333 4.344,3.531 0.156,0.198 10 false 6 4.5,3.448 5.115,3.646 0.615,0.198 10 false OSR 5.844,3.552 6.458,3.75 0.615,0.198 10 false CPU 3.427,0.552 4.042,0.75 0.615,0.198 10 false PBD 3.094,1.094 4.25,1.333 1.156,0.24 10 false ECU-B NO. 2 2.958,1.625 3.938,1.885 0.979,0.26 10 false ECU-IG1 NO. 4 1.438,0.396 2.906,0.635 1.469,0.24 10 false from Auxiliary Battery 1.49,1.469 2.948,1.688 1.458,0.219 10 false from IG1-NO.1 Relay 3.156,1.958 3.771,2.156 0.615,0.198 10 false OSL 3.135,3.458 3.75,3.656 0.615,0.198 10 false OSR 3.573,1.927 3.729,2.125 0.156,0.198 10 false 1 3.521,3.427 3.677,3.625 0.156,0.198 10 false 1 1.948,3.417 2.104,3.615 0.156,0.198 10 false 2 1.958,1.938 2.115,2.135 0.156,0.198 10 false 2 2.188,1.958 2.802,2.156 0.615,0.198 10 false OSLE 2.167,3.448 2.781,3.646 0.615,0.198 10 false OSRE 4.063,4.854 4.521,5.052 0.458,0.198 10 false W18 4.135,4.646 4.448,4.844 0.313,0.198 10 false 24 4.458,4.76 5.073,4.958 0.615,0.198 10 false OSE 4.063,7.719 4.521,7.917 0.458,0.198 10 false W19 4.156,7.521 4.469,7.719 0.313,0.198 10 false 10 4.458,7.615 5.073,7.813 0.615,0.198 10 false GND 4.688,8.229 6.583,8.552 1.896,0.323 10 false Multiplex Network Door ECU 0.781,8.469 2.521,8.771 1.74,0.302 10 false : CAN Communication Line 1.646,2.542 2.104,2.74 0.458,0.198 10 false W10 1.646,2.698 4.104,3 2.458,0.302 10 false Power Back Door Sensor Assembly LH 1.667,4.042 2.167,4.24 0.5,0.198 10 false W9 1.688,4.229 4.146,4.531 2.458,0.302 10 false Power Back Door Sensor Assembly RH 1.438,0.917 2.906,1.156 1.469,0.24 10 false from Auxiliary Battery 1.354,6.458 5.333,6.656 3.979,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The power back door system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power back door system after confirming that the CAN communication system is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.

Check that the shift position indicator operates correctly and the speedometer indicates 0 km/h (0 mph) when the vehicle is stopped with the hybrid control system started.

OK:

Combination meter operates normally



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC is not output



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - AUXILIARY BATTERY AND BODY GROUND)
a.
B426089C37
1.469,0.365 1.885,0.646 0.417,0.281 1.51,2.625 1.906,2.885 0.396,0.26 1,0.396 0.833,0.396 0.833,0.396 0.833,1.229 true 0.771,0.146 0.604,0.146 0.604,0.146 0.604,1.229 true 1,4.417 1.229,4.417 1.229,4.417 1.229,3.75 true 2.344,2.552 2.177,2.552 2.177,2.552 2.177,3.417 true 1.531,0.417 1.99,0.615 0.458,0.198 10 false W18 1.563,2.667 2.021,2.865 0.458,0.198 10 false W19 1.073,0.323 1.385,0.521 0.313,0.198 10 false IG 0.667,4.333 1.281,4.531 0.615,0.198 10 false GND 0.833,0.073 1.448,0.271 0.615,0.198 10 false ECUB 2.406,2.479 2.677,2.74 0.271,0.26 10 false B 0.125,0.125 0.74,0.323 0.615,0.198 10 false *a
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W19-10 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W18-20 (ECUB) - Body ground Ignition switch off*1
Always*2
11 to 14 V
W19-1 (B) - Body ground Ignition switch off*1
Always*2
11 to 14 V
W18-18 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (PBD MAIN SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (PBD MAIN SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Main SW Power back door ON/OFF signal OFF or ON Customize setting displayed -
Body Electrical > Back Door > Data List
Tester Display
PBD Main SW
50003 159 7
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (PBD TOUCH SENSOR)

NG

5.READ VALUE USING GTS (PBD TOUCH SENSOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Touch Sensor (Right) Power back door sensor assembly RH signal OFF, ON or Open OFF: Power back door sensor assembly RH not pressed
ON: Power back door sensor assembly RH pressed
Open: Power back door sensor assembly RH circuit open
-
PBD Touch Sensor (Left) Power back door sensor assembly LH signal OFF, ON or Open OFF: Power back door sensor assembly LH not pressed
ON: Power back door sensor assembly LH pressed
Open: Power back door sensor assembly LH circuit open
-
Body Electrical > Back Door > Data List
Tester Display
PBD Touch Sensor (Right)
PBD Touch Sensor (Left)
50003 159 5,6

Result:
Result Proceed to
The values of Data List items "PBD Touch Sensor (Right)" and "PBD Touch Sensor (Left)" change to "ON" or "OFF" in accordance with the operation of the sensors. A
The value of Data List item "PBD Touch Sensor (Right)" does not change to "ON" or "OFF" in accordance with the operation of the power back door sensor assembly RH. B
The value of Data List item "PBD Touch Sensor (Left)" does not change to "ON" or "OFF" in accordance with the operation of the power back door sensor assembly LH. C



A

REPLACE MULTIPLEX NETWORK DOOR ECU

B

6.INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH

C

8.INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH
6.INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH

OK

7.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the W18 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W9-1 (OSR) - W18-6 (OSR) Always Below 1 Ω
W9-2 (OSRE) - W18-24 (OSE) Always Below 1 Ω
W9-1 (OSR) or W18-6 (OSR) - Body ground Always 10 kΩ or higher
W9-2 (OSRE) or W18-24 (OSE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH

OK

9.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

9.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the W18 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W10-1 (OSL) - W18-26 (OSL) Always Below 1 Ω
W10-2 (OSLE) - W18-24 (OSE) Always Below 1 Ω
W10-1 (OSL) or W18-26 (OSL) - Body ground Always 10 kΩ or higher
W10-2 (OSLE) or W18-24 (OSE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR