1.INSPECT TIRES
Inspect the tires for wear and proper inflation pressure.
| Tire Size | Cold Tire Inflation Pressure | |
|---|---|---|
| Front | Rear | |
|
*1: For driving under 160 km/h (99 mph). *2: For driving at 160 km/h (100 mph) or over |
||
| 235/65R18 106V | 250 kPa (2.5 kgf/cm2, 36 psi) | 250 kPa (2.5 kgf/cm2, 36 psi) |
| 235/55R20 102V | 250 kPa (2.5 kgf/cm2, 36 psi)*1
260 kPa (2.6 kgf/cm2, 38 psi)*2 |
250 kPa (2.5 kgf/cm2, 36 psi)*1
260 kPa (2.6 kgf/cm2, 38 psi)*2 |
Perform initialization.
for HV Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for Gasoline Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Tire pressure adjustment method when warm:
Adjust the tire pressure so that the displayed value is equal to the set pressure.
Perform initialization and check that initialization completes.
for HV Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for Gasoline Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Check and record the value of the Data List item "Temperature in Tire". (Ts)
Check and record the ambient temperature during tire pressure adjustment. (Tm)
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
| Tester Display |
|---|
| ID 1 Tire Inflation Pressure |
| ID 2 Tire Inflation Pressure |
| ID 3 Tire Inflation Pressure |
| ID 4 Tire Inflation Pressure |
| ID 5 Tire Inflation Pressure |
| ID 1 Temperature in Tire |
| ID 2 Temperature in Tire |
| ID 3 Temperature in Tire |
| ID 4 Temperature in Tire |
| ID 5 Temperature in Tire |
Using a dial indicator, check the runout of the tires.
1.4 mm (0.0551 in.)
Measure the runout with the wheel assembly removed from the vehicle.
2. ROTATE TIRES
Remove the wheel assembly.
|
Front |
Rotate the tires as shown in the illustration.
Install the wheel assembly.
Perform initialization.
for HV Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for Gasoline Model: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
3.INSPECT AND ADJUST WHEEL BALANCE
Inspect and adjust the off-the-car balance.
| *a | 25 mm (0.984 in.) |
for 20 Inch Wheel:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
| *a | 25 mm (0.984 in.) |
for 18 Inch Wheel:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use stick-on type balance weights for both the inner and outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
4.INSPECT FRONT AXLE HUB BEARING
5.INSPECT REAR AXLE HUB BEARING
for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 2WD)>ON-VEHICLE INSPECTION
for 4WD/AWD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>ON-VEHICLE INSPECTION