Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for 4WD/AWD) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417448 REAR AXLE HUB(for 4WD/AWD) G

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for 4WD/AWD)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub and bearing assembly on-vehicle inspection are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
for HV Model
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

Hide 2.REMOVE REAR WHEEL

Hide 890C0A 3.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 47850 4.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 5.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 42431 6.REMOVE REAR DISC

Hide 7.INSPECT REAR AXLE HUB BEARING LOOSENESS

a.
C424672

Using a dial indicator, check for looseness near the center of the rear axle hub.

Maximum Looseness:

0.05 mm (0.00196 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the rear skid control sensor.



HINT:

If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 8.INSPECT REAR AXLE HUB RUNOUT

a.
C424673

Using a dial indicator, check for runout on the surface of the rear axle hub outside the rear axle hub bolts.

Maximum Runout:

0.08 mm (0.00314 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.

·

Keep the magnet of the dial indicator away from the rear skid control sensor.



HINT:

If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 42431 9.INSTALL REAR DISC

Hide 10.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 47850 11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 890C0A 12.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 13.INSTALL REAR WHEEL

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


e.

Turn the ignition switch to ON (READY).


f.

Depress the brake pedal and release it.