Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P001400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1  P001500  Camshaft Position "B" - Timing Over-Retarded Bank 1  P002400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2  P002500  Camshaft Position "B" - Timing Over-Retarded Bank 2  


DESCRIPTION

Refer to DTC P001313.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P001313

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 1])

·

Camshaft timing exhaust gear assembly (bank 1)

·

Oil control valve filter (for exhaust camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0014
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 1])

·

Camshaft timing exhaust gear assembly (bank 1)

·

Oil control valve filter (for exhaust camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0015
P002400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 2])

·

Camshaft timing exhaust gear assembly (bank 2)

·

Oil control valve filter (for exhaust camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0024
P002500 Camshaft Position "B" - Timing Over-Retarded Bank 2 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

·

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 2])

·

Camshaft timing exhaust gear assembly (bank 2)

·

Oil control valve filter (for exhaust camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0025

MONITOR DESCRIPTION

The ECM optimizes the exhaust timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly. The camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) is operated to control the oil pressure supplied to the camshaft timing exhaust gear assembly based on this signal. The camshaft timing exhaust gear assembly can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.

Example:

A DTC is stored when the following conditions are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA.

(b)

After the above condition is met, the cam timing oil control solenoid is forcibly activated for 60 seconds.



DTC P001400 and P002400 (Advanced Camshaft Timing) is subject to 2 trip detection logic.

DTC P001500 and P002500 (Retarded Camshaft Timing) is subject to 1 trip detection logic.

These DTCs indicate that the camshaft timing exhaust gear assembly cannot operate properly due to a camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) malfunction or the presence of foreign matter in the camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]).

MONITOR STRATEGY

Required Sensors/Components (Main) Cam timing oil control solenoid assembly (for exhaust camshaft)
Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft])
Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Crankshaft position sensor
VVT sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232050E68
6.719,2.635 6.333,3.5 6.333,3.5 6.25,3.5 false 4.156,2.646 3.833,3.51 3.833,3.51 3.771,3.51 false 1.365,2.365 1.656,2.521 0.292,0.156 10 false [A] 1.875,2.021 2.135,2.281 0.26,0.26 10 false [B] 3.01,1 3.25,1.146 0.24,0.146 10 false [C] 4.052,2.313 4.313,2.542 0.26,0.229 10 false [D] 4.281,3.135 4.563,3.385 0.281,0.25 10 false [E] 5.448,2.219 5.708,2.469 0.26,0.25 10 false [F]* 6.615,2.302 6.927,2.583 0.313,0.281 10 false [G] 6.833,3.156 7.104,3.375 0.271,0.219 10 false [H] 0.167,2.313 1.083,2.792 0.917,0.479 10 false Ignition Switch ON 0.708,2.063 1.094,2.25 0.385,0.188 10 false Idling 0.177,1.094 1.115,1.552 0.938,0.458 10 false Approximately 60 km/h 0.167,0.375 1.063,0.635 0.896,0.26 10 false Vehicle Speed 1.615,2.771 2.417,2.969 0.802,0.198 10 false Warming up 2.563,2.771 3.781,3.021 1.219,0.25 10 false 10 minutes or more 2.583,3.427 3.875,3.604 1.292,0.177 10 false 3 minutes or more 2.542,0.031 7.052,0.635 4.51,0.604 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5,3.438 6.281,3.667 1.281,0.229 10 false 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Idle the engine for 3 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P001400, P001500, P002400 or P002500.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [F] through [H].



16.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


17.

Idle the engine for 3 minutes or more [G].

18.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Check the DTC judgment result again.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Timing Over Advanced
(Valve timing is out of specified range)
Timing Over Retarded
(Valve timing is out of specified range)
Bank 1 P001400 P001500
Bank 2 P002400 P002500

·

If DTC P001400 or P001500 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.

·

If DTC P002400 or P002500 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400, P001500, P002400 OR P002500)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001400, P001500, P002400 or P002500 is output A
DTC P001400, P001500, P002400 or P002500 and other DTCs are output B


HINT:

If any DTCs other than P001400, P001500, P002400 or P002500 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5
Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
50004 372 46
OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Change Angle Bank 2].

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B


HINT:

DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.




A

B

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

6.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])

NG

12.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
6.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])

OK

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

14.REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])
7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

A370146C01
0.896,3.031 1.021,3.031 1.021,3.031 1.552,3.24 false 1.75,3.219 2.25,3.49 2.25,3.49 2.385,3.49 false 1.604,0.708 1.229,1.365 1.229,1.365 1.615,1.01 false 0.927,0.833 1.427,0.406 1.427,0.406 0.927,0.688 false 5.594,0.927 6.115,0.365 6.115,0.365 5.615,0.667 false 6.26,0.667 5.729,1.344 5.729,1.344 6.25,0.813 false 1.094,1.323 1.406,1.479 0.313,0.156 10 false *a 2.406,3.396 2.719,3.552 0.313,0.156 10 false *b 0.76,2.927 1.073,3.083 0.313,0.156 10 false *c 1.427,0.281 1.74,0.438 0.313,0.156 10 false *a 6.094,0.229 6.406,0.385 0.313,0.156 10 false *a 5.583,1.313 5.896,1.469 0.313,0.156 10 false *a
*a Timing Mark *b TDC Timing Mark
*c Groove - -



b.

Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

8.INSPECT OIL CONTROL VALVE FILTER (FOR EXHAUST CAMSHAFT)

NG

9.CHECK ENGINE MECHANICAL SYSTEM
8.INSPECT OIL CONTROL VALVE FILTER (FOR EXHAUST CAMSHAFT)
A370163C01
1.698,0.844 1.927,0.594 1.927,0.594 2.094,0.594 false 5.417,0.885 5.646,0.635 5.646,0.635 5.813,0.635 false 0.917,0.333 1.229,0.583 0.313,0.25 12 false A 4.031,0.333 4.333,0.563 0.302,0.229 12 false B 2.125,0.5 2.438,0.656 0.313,0.156 10 false *1 5.844,0.542 6.156,0.698 0.313,0.156 10 false *1
A for Exhaust Camshaft of Bank 1 B for Exhaust Camshaft of Bank 2
*1 Oil Control Valve Filter - -


a.

Remove the oil control valve filter (for exhaust camshaft of bank 1) or oil control valve filter (for exhaust camshaft of bank 2).



b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

16.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER (FOR EXHAUST CAMSHAFT)

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B




A

B

12.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

NEXT

13.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])
13.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])

OK

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)

NG

14.REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])
14.REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])

NEXT

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
15.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5
Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
50004 372 46
OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Change Angle Bank 2].

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

END

NG

16.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
16.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400, P001500, P002400 or P002500 is output B




A

END

B