Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A373204E63
1.26,0.885 1.875,1.083 0.615,0.198 10 false CANH 1.292,1.594 1.906,1.792 0.615,0.198 10 false CANL 2.833,0.875 3.448,1.073 0.615,0.198 10 false CA5H 5.51,1.573 6.125,1.771 0.615,0.198 10 false CANL 5.51,0.865 6.125,1.063 0.615,0.198 10 false CANH 2.844,1.573 3.458,1.771 0.615,0.198 10 false CA5L 3.927,0.875 4.542,1.073 0.615,0.198 10 false CA4H 3.948,1.583 4.563,1.781 0.615,0.198 10 false CA4L 0.927,3.219 3.042,3.51 2.115,0.292 10 false : CAN Communication Line 2.896,2.25 4.438,2.5 1.542,0.25 10 false Network Gateway ECU 0.083,2.25 2.021,2.573 1.938,0.323 10 false Combination Meter Assembly 6.073,2.26 6.583,2.542 0.51,0.281 10 false ECM 6.094,2.094 6.708,2.292 0.615,0.198 10 false A28 2.906,2.094 3.521,2.292 0.615,0.198 10 false H59 0.094,2.094 0.708,2.292 0.615,0.198 10 false H21 1.729,0.708 2.344,0.906 0.615,0.198 10 false 32 1.729,1.417 2.344,1.615 0.615,0.198 10 false 31 2.604,0.708 3.219,0.906 0.615,0.198 10 false 15 2.604,1.417 3.219,1.615 0.615,0.198 10 false 16 4.365,0.698 4.979,0.896 0.615,0.198 10 false 18 4.365,1.417 4.979,1.615 0.615,0.198 10 false 17 5.26,0.698 5.875,0.896 0.615,0.198 10 false 13 5.26,1.396 5.875,1.594 0.615,0.198 10 false 26

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch ON → engine is started A
Other than above - B



A

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Perform the Health Check using the GTS.


b.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

4.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

4.PERFORM ACTIVE TEST USING GTS
a.

Check the status of the MIL while performing the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150
Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY