If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.
The navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the navigation system will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1543 | Extension Module Disconnected 2 | Navigation ECU disconnected | ·
Navigation ECU ·
Radio and display receiver assembly ·
Harness or connector |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the ignition switch to ACC and wait for 90 seconds.
Press the "MAP" switch and check that the map screen is displayed normally.
| Result | Proceed to |
|---|---|
| Map screen is displayed normally | A |
| Map screen is not displayed normally | B |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 90 seconds.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the H18 navigation ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H18-23 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H18-10 (+B) - Body ground*1 | Ignition switch off | 11 to 14 V |
| H18-10 (+B) - Body ground*2 | Always | 11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the d1 navigation ECU connector.
Disconnect the d3 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d1-4 (US4+) - d3-1 (US4+) | Always | Below 1 Ω |
| d1-5 (US4-) - d3-2 (US4-) | Always | Below 1 Ω |
| d1-6 (UGD4) - d3-3 (UGD4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation ECU with a new or known good one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 90 seconds.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG