Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The telematics transceiver sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E428733E08
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.74,0.917 2.354,1.115 0.615,0.198 10 false 24 5.292,0.917 5.906,1.115 0.615,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.104,1.865 0.719,2.063 0.615,0.198 10 false M38 0.104,2.031 2.719,2.344 2.615,0.313 10 false Stereo Component Amplifier Assembly 5.24,2.073 7.156,2.365 1.917,0.292 10 false Telematics Transceiver 5.24,1.906 5.854,2.104 0.615,0.198 10 false H10

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E412950C18
1.469,0.531 1.906,0.802 0.438,0.271 0.906,0.938 1.385,1.906 false 0.188,0.167 0.438,0.333 0.25,0.167 10 false *a 1.563,0.573 1.896,0.771 0.333,0.198 10 false H10 0.677,0.76 1.302,0.958 0.625,0.198 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the M38 stereo component amplifier assembly connector.


b.

Disconnect the H10 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-24 (TMUT) - H10-17 (MUTE) Always Below 1 Ω
M38-24 (TMUT) or H10-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the H10 telematics transceiver connector.


b.
E412951C16
1.521,0.719 1.938,0.979 0.417,0.26 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.604,0.76 1.99,0.958 0.385,0.198 10 false H10
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-17 (MUTE) - Body ground Ignition switch ACC 2 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY