Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the parking assist ECU are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the parking assist ECU signal circuit
·

Harness or connector

·

Parking assist ECU

·

Radio and display receiver assembly



WIRING DIAGRAM

E436821E01
0.5,2.594 3.073,2.813 2.573,0.219 10 false Radio and Display Receiver Assembly 1.938,0.583 2.25,0.781 0.313,0.198 10 false V+ 1.969,1.25 2.281,1.448 0.313,0.198 10 false V- 2.208,0.49 2.521,0.688 0.313,0.198 10 false 28 2.208,1.156 2.521,1.354 0.313,0.198 10 false 29 3.5,1.469 3.656,1.667 0.156,0.198 10 false * 5,0.563 5.458,0.76 0.458,0.198 10 false NS+ 5,1.24 5.458,1.438 0.458,0.198 10 false NS- 5.01,1.781 5.625,1.979 0.615,0.198 10 false NSG 4.833,0.49 4.99,0.688 0.156,0.198 10 false 7 4.76,1.146 5,1.365 0.24,0.219 10 false 24 4.833,1.698 4.99,1.896 0.156,0.198 10 false 8 4.979,2.302 6.479,2.552 1.5,0.25 10 false Parking Assist ECU 4.979,2.135 5.542,2.354 0.563,0.219 10 false H19 4.719,3.365 6.406,3.563 1.688,0.198 10 false *: Shielded 0.5,2.427 1.115,2.625 0.615,0.198 10 false H2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the H19 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-28 (V+) - H19-7 (NS+) Always Below 1 Ω
H2-29 (V-) - H19-24 (NS-) Always Below 1 Ω
H2-28 (V+) or H19-7 (NS+) - Body ground Always 10 kΩ or higher
H2-29 (V-) or H19-24 (NS-) - Body ground Always 10 kΩ or higher
H19-8 (NSG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the H2 radio and display receiver assembly connector.


b.
E366062C68
1.427,0.198 1.917,0.479 0.49,0.281 0.771,1.76 1.167,1.375 true 1.583,0.25 1.896,0.448 0.313,0.198 10 false H2 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.635,1.771 0.948,1.969 0.313,0.198 10 false V-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-29 (V-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING ASSIST ECU

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT PARKING ASSIST ECU
a.

Reconnect the H19 parking assist ECU connector.


b.
E366062C61
1.5,0.25 1.917,0.5 0.417,0.25 1.167,1.344 0.729,0.896 0.729,0.896 0.583,0.896 false 1.271,1.365 1.063,1.896 1.063,1.896 0.917,1.896 false 1.615,0.302 2.115,0.542 0.5,0.24 10 false H2 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,0.813 0.729,1.031 0.354,0.219 10 false V- 0.698,1.813 1.052,2.031 0.354,0.219 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the parking assist ECU.

HINT:

A waterproof connector is used for the parking assist ECU. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal H2-28 (V+) - H2-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the parking assist ECU.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG