Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display)
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly and telephone microphone assembly, and the map light assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E368001E15
0.677,3.146 2.083,3.646 1.406,0.5 10 false Telephone Microphone Assembly 2.792,3.135 4.552,3.563 1.76,0.427 10 false Map Light Assembly 5.583,4.281 6.01,4.5 0.427,0.219 10 false H3 5.75,5.604 6.938,6.021 1.188,0.417 10 false Radio and Display Receiver Assembly 2.979,5.583 3.406,5.802 0.427,0.219 10 false H18 2.979,5.75 4.042,6 1.063,0.25 10 false Navigation ECU 3.427,4.292 3.854,4.51 0.427,0.219 10 false MIC+ 2.75,0.792 3.177,1.01 0.427,0.219 10 false B 3.896,0.802 4.323,1.021 0.427,0.219 10 false R11 5.583,0.792 6.01,1.01 0.427,0.219 10 false H2 5.917,0.792 6.458,0.969 0.542,0.177 10 false MACC 5.917,1.26 6.344,1.479 0.427,0.219 10 false MIN+ 5.917,2.188 6.375,2.396 0.458,0.208 10 false SGND 5.927,2.698 6.354,2.917 0.427,0.219 10 false SNS2 3.354,1.25 3.844,1.458 0.49,0.208 10 false MCO+ 5.594,5.01 6.021,5.229 0.427,0.219 10 false 24 5.583,4.563 6.01,4.781 0.427,0.219 10 false 26 5.594,4.073 6.021,4.292 0.427,0.219 10 false 25 5.583,1.531 6.01,1.75 0.427,0.219 10 false 22 5.583,1.073 6.01,1.292 0.427,0.219 10 false 21 5.573,0.594 6,0.813 0.427,0.219 10 false 23 3.979,0.573 4.406,0.792 0.427,0.219 10 false 4 3.938,1.063 4.365,1.281 0.427,0.219 10 false 13 3.969,1.552 4.396,1.771 0.427,0.219 10 false 5 3.927,1.99 4.354,2.208 0.427,0.219 10 false 11 3.927,2.49 4.354,2.708 0.427,0.219 10 false 14 2.75,2.479 3.177,2.698 0.427,0.219 10 false 1 2.76,1.542 3.188,1.76 0.427,0.219 10 false 2 2.76,1.063 3.188,1.281 0.427,0.219 10 false 3 2.75,0.594 3.177,0.813 0.427,0.219 10 false 5 5.594,2.01 6.021,2.229 0.427,0.219 10 false 24 5.583,2.5 6.01,2.719 0.427,0.219 10 false 25 3.354,0.781 3.896,0.958 0.542,0.177 10 false MACC 3.396,1.729 3.885,1.938 0.49,0.208 10 false MCO- 5.927,1.74 6.354,1.958 0.427,0.219 10 false MIN- 3.458,2.188 3.917,2.396 0.458,0.208 10 false GND 3.396,2.698 3.823,2.917 0.427,0.219 10 false SNS2 5.917,4.271 6.406,4.479 0.49,0.208 10 false MCO+ 5.917,4.74 6.406,4.948 0.49,0.208 10 false MCO- 5.927,5.208 6.385,5.417 0.458,0.208 10 false SGND 3.458,4.76 3.885,4.979 0.427,0.219 10 false MIC- 3.833,4.177 4.26,4.396 0.427,0.219 10 false 13 3.844,4.646 4.271,4.865 0.427,0.219 10 false 14 2.76,1.271 3.188,1.49 0.427,0.219 10 false B 2.75,1.74 3.177,1.958 0.427,0.219 10 false B 2.76,2.698 3.188,2.917 0.427,0.219 10 false B 3.896,1.271 4.323,1.49 0.427,0.219 10 false R11 3.896,1.74 4.323,1.958 0.427,0.219 10 false R11 3.885,2.198 4.313,2.417 0.427,0.219 10 false R11 3.885,2.698 4.313,2.917 0.427,0.219 10 false R11 5.583,1.271 6.01,1.49 0.427,0.219 10 false H2 5.594,1.75 6.021,1.969 0.427,0.219 10 false H2 5.573,2.198 6,2.417 0.427,0.219 10 false H2 5.583,2.698 6.01,2.917 0.427,0.219 10 false H2 5.583,4.771 6.01,4.99 0.427,0.219 10 false H3 5.583,5.208 6.01,5.427 0.427,0.219 10 false H3 4.865,5.094 5.167,5.313 0.302,0.219 10 false * 4.833,2.073 5.135,2.292 0.302,0.219 10 false * 0.396,6.344 1.333,6.573 0.938,0.229 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the R11 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-25 (SNS2) - R11-14 (SNS2) Always Below 1 Ω
H2-23 (MACC) - R11-4 (MACC) Always Below 1 Ω
H2-21 (MIN+) - R11-13 (MCO+) Always Below 1 Ω
H2-22 (MIN-) - R11-5 (MCO-) Always Below 1 Ω
H2-25 (SNS2) or R11-14 (SNS2) - Body ground Always 10 kΩ or higher
H2-23 (MACC) or R11-4 (MACC) - Body ground Always 10 kΩ or higher
H2-21 (MIN+) or R11-13 (MCO+) - Body ground Always 10 kΩ or higher
H2-22 (MIN-) or R11-5 (MCO-) - Body ground Always 10 kΩ or higher
H2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the H2 radio and display receiver assembly connector.


b.

Connect the R11 map light assembly connector.


c.
E412759C54
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.188,2.885 1.927,2.146 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.625,0.76 1.938,0.958 0.313,0.198 10 false H2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-24 (SGND) - Body ground Always Below 1 Ω
H2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E430891C02
2.26,1.135 1.948,0.615 false 2.094,1.76 2.25,1.344 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.729,0.417 2.24,0.625 0.51,0.208 10 false MCO- 1.917,1.781 2.448,2.042 0.531,0.26 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 5 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

8.INSPECT MAP LIGHT ASSEMBLY
6.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the H2 radio and display receiver assembly connector.


b.

Connect the R11 map light assembly connector.


c.

Turn the ignition switch to ACC.


d.
E437153C01
1.542,0.344 1.917,0.594 0.375,0.25 2.229,1.5 1.979,0.958 false 2.115,2.26 2.385,1.719 false 1.875,2.292 2.49,2.49 0.615,0.198 10 false MCO+ 1.781,0.74 2.396,0.938 0.615,0.198 10 false MCO- 1.635,0.385 2.25,0.583 0.615,0.198 10 false R11 2.813,3.438 3.427,3.635 0.615,0.198 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 13 (MCO+) and 5 (MCO-) of the R11 map light assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal R11-13 (MCO+) - R11-5 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT MAP LIGHT ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E437127C02
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 2.667,2.104 2.854,1.646 false 2.177,2.083 2.417,1.646 false 2.25,1.417 2.677,0.906 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.969,2.146 2.469,2.365 0.5,0.219 10 false MCO+ 2.521,0.688 3,0.896 0.479,0.208 10 false MCO- 2.5,2.167 2.99,2.396 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.542,0.438 2.021,0.646 0.479,0.208 10 false R11
*a Component without harness connected
(Map Light Assembly (Radio and Display Receiver Assembly Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-13 (MCO+) - B-3 Always Below 1 Ω
R11-5 (MCO-) - B-2 Always Below 1 Ω
R11-13 (MCO+) or B-3 - R11-11 (GND) Always 10 kΩ or higher
R11-5 (MCO-) or B-2 - R11-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E437127C01
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 3.063,2.083 2.854,1.635 false 2.26,1.427 1.823,0.979 false 1.823,2.156 2.25,1.646 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.615,2.188 2.115,2.406 0.5,0.219 10 false SNS2 1.542,0.75 2.021,0.958 0.479,0.208 10 false MCO- 2.917,2.146 3.406,2.375 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.521,0.427 2,0.635 0.479,0.208 10 false R11
*a Component without harness connected
(Map Light Assembly (Radio and Display Receiver Assembly Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - R11-14 (SNS2) Always Below 1 Ω
B-2 - R11-5 (MCO-) Always Below 1 Ω
B-1 or R11-14 (SNS2) - R11-11 (GND) Always 10 kΩ or higher
B-2 or R11-5 (MCO-) - R11-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the H3 radio and display receiver assembly connector.


b.

Disconnect the H18 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-25 (MCO+) - H18-13 (MIC+) Always Below 1 Ω
H3-26 (MCO-) - H18-14 (MIC-) Always Below 1 Ω
H3-25 (MCO+) or H18-13 (MIC+) - Body ground Always 10 kΩ or higher
H3-26 (MCO-) or H18-14 (MIC-) - Body ground Always 10 kΩ or higher
H3-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)
a.

Disconnect the H18 navigation ECU connector.


b.

Turn the ignition switch to ACC.


c.
E368005C57
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 false 0.833,2.083 1.188,1.469 false 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.604,0.469 2,0.698 0.396,0.229 10 false H18 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU)


Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H18-13 (MIC+) - H18-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY