11101
1.INSPECT CYLINDER HEAD SUB-ASSEMBLY
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and exhaust manifold (TWC: Front Catalyst).
| *a | Bottom Side | *b | Intake Manifold Side |
| *c | Exhaust Manifold (TWC: Front Catalyst) Side | - | - |
| Item | Specified Condition |
|---|---|
| Bottom side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.10 mm (0.00394 in.) |
| Exhaust manifold (TWC: Front Catalyst) side | 0.10 mm (0.00394 in.) |
If the warpage is more than the maximum, replace the cylinder head sub-assembly.
Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.
If cracks are found, replace the cylinder head sub-assembly.
13711M
2.INSPECT INTAKE VALVE COMPRESSION SPRING
Using a vernier caliper, measure the free length of the intake valve compression spring.
58.81 mm (2.32 in.)
If the free length is not as specified, replace the intake valve compression spring.
| *a | Deviation |
| *b | 42.0 mm (1.65 in.) |
Using a steel square, measure the deviation of the intake valve compression spring.
1.0 mm (0.0394 in.)
If the deviation is more than the maximum, replace the intake valve compression spring.
13715H
3.INSPECT EXHAUST VALVE COMPRESSION SPRING
Using a vernier caliper, measure the free length of the exhaust valve compression spring.
61.08 mm (2.40 in.)
If the free length is not as specified, replace the exhaust valve compression spring.
| *a | Deviation |
| *b | 44.0 mm (1.73 in.) |
Using a steel square, measure the deviation of the exhaust valve compression spring.
1.0 mm (0.0394 in.)
If the deviation is more than the maximum, replace the exhaust valve compression spring.
13711
4.INSPECT INTAKE VALVE
Using a micrometer, measure the diameter of the intake valve stem.
5.470 to 5.485 mm (0.215 to 0.216 in.)
If the intake valve stem diameter is not as specified, check the intake valve guide bush oil clearance.
| *a | Margin Thickness |
Using a vernier caliper, measure the intake valve head margin thickness.
1.0 mm (0.0394 in.)
0.5 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the intake valve.
| *a | Overall Length |
Using a vernier caliper, measure the overall length of the intake valve.
104.45 mm (4.11 in.)
103.95 mm (4.09 in.)
If the overall length is less than the minimum, replace the intake valve.
13715
5.INSPECT EXHAUST VALVE
Using a micrometer, measure the diameter of the exhaust valve stem.
5.465 to 5.480 mm (0.215 to 0.216 in.)
If the exhaust valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.
| *a | Margin Thickness |
Using a vernier caliper, measure the exhaust valve head margin thickness.
1.0 mm (0.0394 in.)
0.5 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the exhaust valve.
| *a | Overall Length |
Using a vernier caliper, measure the overall length of the exhaust valve.
108.7 mm (4.28 in.)
108.2 mm (4.26 in.)
If the overall length is less than the minimum, replace the exhaust valve.
6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the valve guide bush.
5.51 to 5.53 mm (0.217 to 0.218 in.)
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
| Item | Specified Condition |
|---|---|
| Intake Side | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust Side | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
|---|---|
| Intake Side | 0.080 mm (0.00315 in.) |
| Exhaust Side | 0.10 mm (0.00394 in.) |
Oil clearance = Valve guide bush inside diameter - Valve stem diameter
If the oil clearance is more than the maximum, replace the valve and valve guide bush.
7.INSPECT INTAKE VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
| *a | Width |
Lightly press the valve face against the intake valve seat.
Do not rotate the valve while pressing it.
Check the valve face and intake valve seat by using the following procedure:
If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.
If the valve face is not concentric, replace the intake valve.
If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.
If the valve face is not concentric, replace the cylinder head sub-assembly.
Measure the width of the contact area of the intake valve seat and valve face.
1.0 to 1.4 mm (0.0394 to 0.0551 in.)
8.INSPECT EXHAUST VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
| *a | Width |
Lightly press the valve face against the exhaust valve seat.
Do not rotate the valve while pressing it.
Check the valve face and exhaust valve seat by using the following procedure:
If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.
If the valve face is not concentric, replace the exhaust valve.
If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.
If the valve face is not concentric, resurface the exhaust valve seat.
Measure the width of the contact area of the exhaust valve seat and valve face.
1.3 to 1.7 mm (0.0512 to 0.0669 in.)
13511
9.INSPECT CAMSHAFT THRUST CLEARANCE
Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.
Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly on the cylinder head sub-assembly.
Install the camshaft bearing caps.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY
Install the camshaft housing sub-assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY
Using a dial indicator, measure the thrust clearance while moving the camshaft and No. 2 camshaft back and forth.
| Item | Specified Condition |
|---|---|
| Camshaft | 0.04 to 0.17 mm (0.00157 to 0.00669 in.) |
| No. 2 Camshaft | 0.04 to 0.17 mm (0.00157 to 0.00669 in.) |
| Item | Specified Condition |
|---|---|
| Camshaft | 0.22 mm (0.00866 in.) |
| No. 2 Camshaft | 0.22 mm (0.00866 in.) |
If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.