This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL STRAIGHT PIN
It is not necessary to remove the straight pins unless they are being replaced.
No. 2 timing chain cover assembly side:
Using a plastic hammer, tap in 4 new straight pins to the No. 2 timing chain cover assembly.
| *a | Protrusion Height | - | - |
3.0 to 5.0 mm (0.118 to 0.197 in.)
5.0 to 7.0 mm (0.197 to 0.276 in.)
Timing chain cover assembly side:
| *a | Protrusion Height |
Using a plastic hammer, tap in a new straight pin to the timing chain cover assembly.
18.5 to 19.5 mm (0.728 to 0.768 in.)
2.INSTALL RING PIN
It is not necessary to remove the ring pins unless they are being replaced.
Camshaft housing sub-assembly side:
| *a | Protrusion Height |
Using a plastic hammer, tap in 10 new ring pins to the camshaft housing sub-assembly.
3.2 to 4.3 mm (0.126 to 0.169 in.)
Stiffening crankcase assembly side:
| *a | Protrusion Height |
Using a plastic hammer, tap in 6 new ring pins to the stiffening crankcase assembly.
3.5 to 4.5 mm (0.138 to 0.177 in.)
4.3 to 5.3 mm (0.169 to 0.209 in.)
Timing chain cover assembly side:
| *a | Protrusion Height |
Using a plastic hammer, tap in a new ring pin to the timing chain cover assembly.
3.0 to 5.0 mm (0.118 to 0.197 in.)
3.INSTALL STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Stiffening crankcase assembly side:
| *a | 9 mm (0.354 in.) |
| *b | 19 mm (0.748 in.) |
Using an E6 "TORX" socket wrench, install the 2 stud bolts to the stiffening crankcase assembly.
Timing chain cover assembly side:
| *a | 21 mm (0.827 in.) |
| *b | 9 mm (0.354 in.) |
| *c | 34 mm (1.34 in.) |
Using an E6 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.
4.INSTALL WIRE HARNESS CLAMP BRACKET
Stiffening crankcase assembly side:
Install the wire harness clamp bracket to the stiffening crankcase assembly with the bolt.
Camshaft housing sub-assembly side:
Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.
5.INSTALL STRAIGHT SCREW PLUG
Using a 10 mm hexagon socket wrench, install the 3 straight screw plugs and 3 new gaskets to the stiffening crankcase assembly.
13620B
6.INSTALL ENGINE BALANCER ASSEMBLY
Install the engine balancer assembly to the stiffening crankcase assembly with the 2 bolts.
11420
7.INSTALL STIFFENING CRANKCASE ASSEMBLY
| *a | 270° |
| *b | Crankshaft Timing Gear Key Groove |
Rotate the crankshaft clockwise so that the crankshaft timing gear key groove is at the position 270° from the bottom as shown in the illustration.
| *a | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Area | Specified Condition |
|---|---|
| Continuous Line | Diameter 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
Remove any oil from the contact surfaces.
Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after the installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Do not start the engine for at least 2 hours after installation.
After installation, if the seal packing has seeped out, wipe it off.
| *a | Cutout |
Check that the front cutouts are as shown in the illustration.
Clean the bolts and bolt holes.
| *a | Bolt Type |
Temporarily install the stiffening crankcase assembly with the 11 bolts.
| Item | Length |
|---|---|
| Bolt (A) | 40 mm (1.57 in.) |
| Bolt (B) | 90 mm (3.54 in.) |
| Bolt (C) | 170 mm (6.69 in.) |
| *a | Tightening Order |
Tighten the 11 bolts in the order shown in the illustration to install the stiffening crankcase assembly.
15100
8.INSTALL OIL PUMP ASSEMBLY
15167
9.INSTALL OIL PUMP BRACKET
| *a | Front Mark |
Install the oil pump bracket with the 2 bolts as shown in the illustration.
89491
10.INSTALL ENGINE OIL LEVEL SENSOR
15104
11.INSTALL OIL STRAINER SUB-ASSEMBLY
Apply a light coat of engine oil to a new oil strainer gasket.
Using an 8 mm socket wrench, install the oil strainer sub-assembly and oil strainer gasket with the bolt.
12102A
12.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
| *a | Seal Packing |
| *b | 4.5 mm (0.177 in.) |
| *c | 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.5 mm (0.0984 to 0.138 in.)
Remove any oil from the contact surfaces.
Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Do not add engine oil for at least 2 hours after the installation.
| *a | Nut |
Install the No. 2 oil pan sub-assembly with the 11 bolts and 2 nuts in several steps in the order shown in the illustration.
12101A
13.INSTALL OIL PAN DRAIN PLUG
Install a new gasket and the oil pan drain plug to the No. 2 oil pan sub-assembly.
15600A
14.INSTALL OIL FILTER UNION
Using a 12 mm straight hexagon wrench, install the oil filter union to the stiffening crankcase assembly.
15601
15.INSTALL OIL FILTER SUB-ASSEMBLY
11401L
16.INSTALL REAR ENGINE OIL SEAL
11445
17.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the cylinder block water jacket spacer to the exhaust side of the cylinder block sub-assembly.
11115
18.INSTALL CYLINDER HEAD GASKET
11101
19.INSTALL CYLINDER HEAD SUB-ASSEMBLY
The cylinder head set bolts are tightened in 3 progressive steps.
Place the cylinder head sub-assembly on the cylinder block sub-assembly.
Ensure that the contact surface of the cylinder head sub-assembly is free of oil.
Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.
Do not allow oil to adhere to the bottom of the cylinder head sub-assembly.
Clean the bolt and bolt hole.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
|
Front of Engine |
Install the 10 plate washers to the 10 cylinder head set bolts.
| Item | Length |
|---|---|
| Bolt (A) | 139.1 to 140.9 mm (5.48 to 5.55 in.) |
| Bolt (B) | 149.1 to 150.9 mm (5.87 to 5.94 in.) |
Step 1:
|
Front of Engine |
Using a 12 mm bi-hexagonal wrench, install and uniformly tighten the 10 cylinder head set bolts in several steps in the order shown in the illustration.
Be careful not to drop the plate washers into the cylinder head sub-assembly.
Step 2:
| *a | Paint Mark |
| *b | 90° |
| *c | 90° |
|
Front of Engine |
Mark each cylinder head set bolt head with paint as shown in the illustration.
Tighten the cylinder head set bolts 90° in the order shown in step 1.
Step 3:
Tighten the cylinder head set bolts another 90° in the order shown in step 1.
Check that the paint marks are now facing rearward.
Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
16206
20.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Using an 8 mm socket wrench, install the water by-pass pipe sub-assembly and a new gasket to the cylinder head sub-assembly with the 2 bolts.
13512
21.INSTALL NO. 2 CAMSHAFT
Perform "Inspection After Repair" after replacing the No. 2 camshaft.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Clean the camshaft journals and camshaft housing sub-assembly.
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.
Install the No. 2 camshaft to the camshaft housing sub-assembly.
13511
22.INSTALL CAMSHAFT
Perform "Inspection After Repair" after replacing the camshaft.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Clean the camshaft journals and camshaft housing sub-assembly.
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.
Install the camshaft to the camshaft housing sub-assembly.
23.INSTALL CAMSHAFT BEARING CAP
Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap in their correct locations.
Uniformly tighten the 8 bolts in the order shown in the illustration.
Check the torque of each bolt again.
Check that the camshaft and No. 2 camshaft turns smoothly.
13716
24.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem cap ends.
Install the 16 valve stem caps to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Do not drop the valve stem caps into the cylinder head sub-assembly.
13750
25.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the 16 valve lash adjuster assemblies before installing them.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
13801
26.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster Assembly |
Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.
Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.
Install the same parts in the same combination to their original locations.
11103
27.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster Assembly |
| *a | Incorrect |
| *b | Correct |
Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
| *a | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surfaces.
Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Do not add engine oil for at least 2 hours after installation.
| *a | 28° to 58° |
| *b | 43° to 73° |
| *c | No. 1 Cylinder Cam Nose |
Position the camshaft and No. 2 camshaft as shown in the illustration.
Temporarily install the camshaft housing sub-assembly with the 18 bolts.
| Item | Length |
|---|---|
| Bolt (A) | 40 mm (1.57 in.) |
| Bolt (B) | 65 mm (2.56 in.) |
Tighten the 18 bolts in several steps in the order shown in the illustration.
After installation, if the seal packing has seeped out, wipe it off.
23477
28.INSTALL FUEL PUMP LIFTER GUIDE
Using an 8 mm socket wrench, install the fuel pump lifter guide to the No. 4 camshaft bearing cap with the 2 bolts.
13471A
29.INSTALL CRANKSHAFT TIMING GEAR KEY
Using a plastic hammer, tap in the 2 crankshaft timing gear keys.
Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.
15703A
30.INSTALL OIL NOZZLE VALVE SUB-ASSEMBLY
Install the oil nozzle valve sub-assembly to the cylinder block sub-assembly.
11310
31.INSTALL TIMING CHAIN COVER ASSEMBLY
Clean the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, oil pump assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.
| *a | Timing Chain Cover Assembly Side | *b | Engine Assembly Side |
Apply seal packing to the timing chain cover assembly as shown in the illustration.
| *a | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | *b | 2.0 to 6.0 mm (0.0787 to 0.236 in.) |
| *c | 10 mm (0.394 in.) | *d | 20 mm (0.787 in.) |
| *e | 4.0 to 6.0 mm (0.157 to 0.236 in.) | *f | 3.0 to 4.0 mm (0.118 to 0.157 in.) |
| *g | 8.0 to 10 mm (0.315 to 0.394 in.) | *h | 30 mm (1.18 in.) |
|
Seal Packing | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Clean the surfaces with non-residue solvent before applying seal packing.
Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Temporarily install the timing chain cover assembly with the 19 bolts.
| Bolt | Length | Width Across Flats |
|---|---|---|
| (A) | 30 mm (1.18 in.) | 12 mm (0.472 in.) |
| (B) | 45 mm (1.77 in.) | 12 mm (0.472 in.) |
Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.
Tighten the 19 bolts in the order shown in the illustration.
13070A
32.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | Knock Pin Hole |
| *b | Knock Pin |
Align and fit the knock pin of the No. 2 camshaft to the knock pin hole of the camshaft timing exhaust gear assembly.
Type A:
Apply a light coat of engine oil to the O-ring of the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
If reusing the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly), be sure to inspect the O-ring.
Using a wrench, hold the hexagonal portion of the No. 2 camshaft.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.
Using a 5 mm hexagon socket wrench, install the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) with the 3 bolts.
Type B:
Using a wrench, hold the hexagonal portion of the No. 2 camshaft.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.
Using a 5 mm hexagon socket wrench, install the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) with the 3 bolts.
Make sure to fit the protrusion of the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) into the cutout of the camshaft timing exhaust gear assembly.
Pull the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) to confirm that is installed securely.
33.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Temporarily install the crankshaft pulley bolt.
| *1 | Crankshaft Timing Gear Key |
| *a | 44.2° |
Rotate the crankshaft 44.2° counterclockwise to position the crankshaft timing gear key as shown in the illustration.
| *a | Timing Mark |
| *b | Knock Pin |
Check that the timing marks of the camshaft timing exhaust gear assembly and knock pin are as shown in the illustration.
13561
34.INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the No. 1 chain vibration damper with the 2 bolts.
13559
35.INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper with the bolt.
13540
36.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
After replacing or removing and installing the No. 1 chain tensioner assembly, an abnormal noise may occur at start up until the oil in the line has had time to replenish.
| *a | End of the plunger |
| *b | Groove |
| *c | Oil Hole |
| *d | Chain Tensioner Slipper |
| *e | Plunger |
While slightly pushing in the plunger of the No. 1 chain tensioner assembly, install the chain tensioner slipper.
Make sure that the end of the plunger is correctly seated in the groove of the chain tensioner slipper.
Make sure that the oil hole of the plunger is facing up.
Using an 8 mm socket wrench, install the bolt.
Install the No. 1 chain tensioner assembly with the nut.
13506
37.INSTALL CHAIN SUB-ASSEMBLY
| *1 | Crankshaft Timing Gear Key |
Set the crankshaft timing gear key as shown in the illustration.
Remove the crankshaft pulley bolt.
Install the crankshaft timing sprocket and chain sub-assembly.
| *a | Paint Mark (Yellow) |
| *b | Timing Mark |
Align the paint mark (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.
| *a | Paint Mark (Pink) |
| *b | Timing Mark |
|
Turn |
Using the hexagonal portion of the No. 2 camshaft, rotate the No. 2 camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing exhaust gear assembly with the paint mark (pink) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing exhaust gear assembly.
13050
38.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | Loosen |
Hold the hexagonal portion of the No. 2 camshaft with a wrench and turn the camshaft timing exhaust gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and crankshaft timing sprocket as shown in the illustration.
| *a | Paint Mark (Pink) |
| *b | Timing Mark |
Align the paint mark (pink) of the chain sub-assembly and the timing mark of the camshaft timing gear assembly.
| *a | Knock Pin Hole |
| *b | Knock Pin |
Align and fit the knock pin of the camshaft to the knock pin hole of the camshaft timing gear assembly.
| *a | Hold |
|
Turn |
Using a wrench, hold the hexagonal portion of the camshaft.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.
Do not disassemble the camshaft timing gear assembly.
Using a 10 mm bi-hexagon socket wrench, install the camshaft timing gear assembly to the camshaft with the bolt.
13507A
39.INSTALL OIL PUMP DRIVE CHAIN SUB-ASSEMBLY
Set the crankshaft timing gear key as shown in the illustration.
| *1 | Oil Pump Drive Sprocket | *2 | Oil Pump Drive Shaft Sprocket |
| *3 | Crankshaft Timing Gear Key | *4 | Oil Pump Assembly |
| *a | Mark Plate | *b | Timing Mark |
Turn the oil pump drive shaft so that the flat face is facing upward.
Align the mark plates with the timing marks of the oil pump drive sprocket and oil pump drive shaft sprocket as shown in the illustration.
Make sure the mark plates of the oil pump drive chain sub-assembly are facing away from the engine assembly.
With the oil pump drive chain sub-assembly placed around the oil pump drive sprocket and oil pump drive shaft sprocket, install the oil pump drive sprocket to the crankshaft and temporarily install the oil pump drive shaft sprocket to the oil pump drive shaft.
| *1 | Chain Tensioner Plate |
| *2 | Chain Damper Spring |
Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate.
Temporarily install the crankshaft pulley assembly with the crankshaft pulley bolt.
Using SST, hold the crankshaft pulley assembly and install the bolt.
Remove SST, the crankshaft pulley bolt and crankshaft pulley assembly.
40.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
11320B
41.INSTALL NO. 2 TIMING CHAIN COVER ASSEMBLY
Clean the contact surfaces of the No. 2 timing chain cover assembly and timing chain cover assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.
| *a | No. 2 Timing Chain Cover Assembly Side | *b | Timing Chain Cover Assembly Side |
|
Seal Packing |
Apply seal packing to the No. 2 timing chain cover assembly as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.5 mm (0.0984 to 0.138 in.)
Clean the surfaces with non-residue solvent before applying seal packing.
Install the No. 2 timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Temporarily install the No. 2 timing chain cover assembly to the timing chain cover assembly with the 20 bolts.
Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.
Tighten the 20 bolts in the order shown in the illustration.
Temporarily install the engine mounting bracket RH to the No. 2 timing chain cover assembly with the 3 bolts.
Tighten the 3 bolts in the order shown in the illustration.
After applying seal packing to the No. 2 timing chain cover assembly, install the engine mounting bracket RH within 10 minutes.
42.INSTALL STRAIGHT SCREW PLUG
Apply adhesive to the straight screw plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using a 10 mm hexagon wrench, install the straight screw plug to the No. 2 timing chain cover assembly.
Install the straight screw plug within 3 minutes of applying adhesive.
Do not add engine oil for at least 1 hour after installation.
11301C
43.INSTALL TIMING CHAIN COVER OIL SEAL
11193
44.INSTALL SPARK PLUG TUBE GASKET
Install 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.
Keep the lip free from foreign matter.
Do not tap in the spark plug tube gaskets at an angle.
11201
45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Apply a light coat of engine oil to a new camshaft bearing cap oil hole gasket.
Install the camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.
Install 7 new cylinder head cover gaskets to the cylinder head cover sub-assembly.
| *a | Seal Packing Diameter: 3.0 to 6.0 mm |
| *b | Mark |
|
Seal Packing |
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 6.0 mm (0.118 to 0.236 in.)
Remove any oil from the contact surfaces.
Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
| *a | O-ring Groove |
| *b | Camshaft Position Sensor Tip |
Perform this procedure only when reusing the 2 camshaft position sensors (for Exhaust Side and for Intake Side).
Clean the O-ring groove of the 2 camshaft position sensors (for Exhaust Side and for Intake Side).
Make sure the O-ring groove is free of foreign matter.
Install a new O-ring to the 2 camshaft position sensors (for Exhaust Side and for Intake Side).
Set the O-ring on the tip of the 2 camshaft position sensors (for Exhaust Side and for Intake Side) and roll it into the O-ring groove with bare hands to install it.
| *1 | O-ring |
| *a | OK |
| *b | NG |
| *c | Seam |
Check if the O-ring is twisted.
Check the entire circumference of the seam of the O-ring for twisting.
Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
Install the cylinder head cover sub-assembly with the 12 bolts (A) and using an 8 mm socket wrench, install 4 new bolts (C) and the 2 camshaft position sensors (for Exhaust Side and for Intake Side) with 2 new bolts (B) in the order shown in the illustration.
| Bolt | Length | Width Across Flats |
|---|---|---|
| (A) | 23.5 mm (0.925 in.) | 10 mm (0.394 in.) |
| (B), (C) | 30 mm (1.18 in.) | 8 mm (0.315 in.) |
If a camshaft position sensor (for Exhaust Side and for Intake Side) has been struck or dropped, replace it.
Make sure that the 2 O-rings are not cracked or moved out of place when installing the 2 camshaft position sensors (for Exhaust Side and for Intake Side).
Do not start the engine for at least 2 hours after installation.
Do not add engine oil for at least 2 hours after installation.
After tightening all bolts, check the tightening torque of the bolts (7) and (8). Retighten them if necessary.
16351
46.INSTALL WATER BY-PASS OUTLET
Using an 8 mm socket wrench, install the water by-pass outlet and a new outlet water pipe gasket to the cylinder head sub-assembly with the 3 bolts.
16331
47.INSTALL WATER OUTLET
Using an 8 mm socket wrench, install the water outlet and a new water outlet gasket to the cylinder head sub-assembly with the 3 bolts.
13470
48.INSTALL CRANKSHAFT PULLEY ASSEMBLY
Align the crankshaft timing gear key with the key groove of the crankshaft pulley assembly.
| *a | Hold |
|
Turn |
Using SST, hold the crankshaft pulley assembly and install the crankshaft pulley bolt.
12204C
49.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
11401G
50.INSTALL CRANKSHAFT POSITION SENSOR
12108A
51.INSTALL OIL FILLER CAP GASKET
Install a new oil filler cap gasket to the oil filler cap sub-assembly.
12180E
52.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.
16264D
53.INSTALL NO. 2 WATER BY-PASS HOSE
Install the No. 2 water by-pass hose to the water by-pass pipe sub-assembly and slide the clip to secure it.
16261G
54.INSTALL NO. 1 WATER BY-PASS HOSE
Install the No. 1 water by-pass hose to the cylinder block sub-assembly and slide the clip to secure it.
15710
55.INSTALL OIL COOLER ASSEMBLY
16032
56.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)
Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with 4 bolts.
16031
57.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
13090E
58.INSTALL CAM TIMING CONTROL MOTOR O-RING
13090D
59.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
60.INSTALL O-RING
15370
61.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
15250
62.INSTALL OIL PRESSURE CONTROL VALVE ASSEMBLY
89448D
63.INSTALL OIL PRESSURE AND TEMPERATURE SENSOR
64.INSTALL STRAIGHT SCREW PLUG
Install the straight screw plug and a new gasket to the cylinder block sub-assembly.
89422A
65.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
89615
66.INSTALL KNOCK CONTROL SENSOR
19100P
67.INSTALL SPARK PLUG