The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.
12211
1.REMOVE NO. 1 VENTILATION CASE
Do not disassemble except if the No. 1 ventilation case to be damaged.
Remove the 4 bolts and No. 1 ventilation case from the cylinder block sub-assembly.
Remove the 3 oil separator gaskets from the No. 1 ventilation case.
2.INSPECT CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.
0.16 to 0.51 mm (0.00630 to 0.0201 in.)
0.512 mm (0.0202 in.)
If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.
3.INSPECT CONNECTING ROD OIL CLEARANCE
| *a | Alignment Mark |
Note the alignment marks on the connecting rod and connecting rod cap so that they can be reinstalled to their original locations.
Using an E12 "TORX" socket wrench, remove the 2 connecting rod bolts and connecting rod cap.
Keep the connecting rod bearing and connecting rod cap together.
Clean the crank pin and connecting rod bearing.
Check the crank pin and connecting rod bearing for pitting and scratches.
If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.
| *a | Plastigage |
Lay a strip of Plastigage on the crank pin.
| *a | Front Mark |
Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod cap to the connecting rod.
Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.
Using an E12 "TORX" socket wrench, install and alternately tighten the 2 connecting rod bolts in several steps.
| *a | Paint Mark |
| *b | 90° |
|
Front of Engine |
Mark the front of each connecting rod bolt with paint.
Tighten the connecting rod bolts 90° as shown in the illustration.
Do not turn the crankshaft during the measurement.
Remove the 2 connecting rod bolts and connecting rod cap.
Keep the connecting rod bearing and connecting rod cap together.
| *a | Plastigage |
| *b | 1, 2 or 3 Mark |
Measure the Plastigage at its widest point.
0.027 to 0.059 mm (0.00106 to 0.00232 in.)
0.059 mm (0.00232 in.)
If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.
If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.
| Mark | Specified Condition |
|---|---|
| 1 | 51.000 to 51.008 mm (2.00787 to 2.00818 in.) |
| 2 | 51.009 to 51.016 mm (2.00822 to 2.00850 in.) |
| 3 | 51.017 to 51.024 mm (2.00854 to 2.00881 in.) |
| Mark | Specified Condition |
|---|---|
| 1 | 1.487 to 1.491 mm (0.0585 to 0.0587 in.) |
| 2 | 1.492 to 1.495 mm (0.0587 to 0.0589 in.) |
| 3 | 1.496 to 1.499 mm (0.0589 to 0.0590 in.) |
47.992 to 48.000 mm (1.88945 to 1.88976 in.)
Remove the Plastigage completely after the measurement.
Perform the inspection above for each cylinder.
4.REMOVE PISTON WITH CONNECTING ROD
| *a | Ridge Reamer |
Using a ridge reamer, remove all the carbon from the top of each cylinder.
Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.
Push the 4 pistons, 4 connecting rods and 4 connecting rod bearings out through the top of the cylinder block sub-assembly.
Keep the connecting rod bearings, connecting rods and connecting rod caps together.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
5.REMOVE CONNECTING ROD BEARING
Remove the 8 connecting rod bearings from the 4 connecting rods and 4 connecting rod caps.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
6.INSPECT CRANKSHAFT THRUST CLEARANCE
Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.
0.09 to 0.19 mm (0.00354 to 0.00748 in.)
0.25 mm (0.00984 in.)
If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.
2.43 to 2.48 mm (0.0957 to 0.0976 in.)
13411
7.REMOVE CRANKSHAFT
Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.
Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.
Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
Remove the crankshaft from the cylinder block sub-assembly.
Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.
Check each crankshaft journal and crankshaft bearing for pitting and scratches.
If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.
11791
8.REMOVE CRANKSHAFT THRUST WASHER
Remove the 2 crankshaft thrust washers from the No. 3 journal position of the cylinder block sub-assembly.
9.REMOVE CRANKSHAFT BEARING
Remove the 5 crankshaft bearings and 5 No. 2 crankshaft bearings from the cylinder block sub-assembly and 5 crankshaft bearing caps.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13011
10.REMOVE PISTON RING SET
| *a | Piston Ring Expander |
Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.
Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13101A
11.REMOVE PISTON PIN HOLE SNAP RING
| *a | Front Mark Cutout Portion |
| *b | Protective Tape |
Using a screwdriver, pry out the 2 piston pin hole snap rings from the piston.
Tape the screwdriver tip before use.
12.REMOVE PISTON
Gradually heat each piston to between 80 and 90°C (176 and 194°F).
Be sure to wear protective gloves.
Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod.
The piston and piston pin are a matched set.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
15708
13.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.
15709
14.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 2 oil nozzle sub-assemblies from the cylinder block sub-assembly.