Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display)
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E368042E13
0.438,3.229 1.833,3.833 1.396,0.604 10 false Telephone Microphone Assembly 2.281,3.219 3.74,3.781 1.458,0.563 10 false Map Light Assembly 5.521,3.375 6.708,3.844 1.188,0.469 10 false Radio and Display Receiver Assembly 2.938,1.854 3.531,2.125 0.594,0.271 10 false SNS2 2.938,2.25 3.531,2.521 0.594,0.271 10 false MCO- 2.146,1.656 2.74,1.927 0.594,0.271 10 false 1 2.146,1.865 2.74,2.135 0.594,0.271 10 false B 3.438,1.865 4.031,2.135 0.594,0.271 10 false R11 2.156,2.063 2.75,2.333 0.594,0.271 10 false 2 3.479,1.646 4.073,1.917 0.594,0.271 10 false 14 2.99,2.656 3.583,2.927 0.594,0.271 10 false GND 5.604,1.885 6.198,2.156 0.594,0.271 10 false SNS2 5.615,2.26 6.208,2.531 0.594,0.271 10 false MIN- 5.365,1.76 5.958,2.031 0.594,0.271 10 false 25 5.365,2.135 5.958,2.406 0.594,0.271 10 false 22 5.521,3.208 6.115,3.479 0.594,0.271 10 false H2 2.156,2.26 2.75,2.531 0.594,0.271 10 false B 3.521,2.063 4.115,2.333 0.594,0.271 10 false 5 3.479,2.458 4.073,2.729 0.594,0.271 10 false 11 3.448,2.25 4.042,2.521 0.594,0.271 10 false R11 3.448,2.656 4.042,2.927 0.594,0.271 10 false R11

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E412759C53
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.625,0.792 1.938,0.99 0.313,0.198 10 false H2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the R11 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-25 (SNS2) - R11-14 (SNS2) Always Below 1 Ω
H2-22 (MIN-) - R11-5 (MCO-) Always Below 1 Ω
H2-25 (SNS2) or R11-14 (SNS2) - Body ground Always 10 kΩ or higher
H2-22 (MIN-) or R11-5 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E430891C02
2.26,1.135 1.948,0.615 false 2.094,1.76 2.25,1.344 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.729,0.417 2.24,0.625 0.51,0.208 10 false MCO- 1.917,1.781 2.448,2.042 0.531,0.26 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 5 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.INSPECT MAP LIGHT ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E437127C01
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 3.063,2.083 2.854,1.635 false 2.26,1.427 1.823,0.979 false 1.823,2.156 2.25,1.646 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.615,2.188 2.115,2.406 0.5,0.219 10 false SNS2 1.542,0.75 2.021,0.958 0.479,0.208 10 false MCO- 2.917,2.146 3.406,2.375 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.521,0.427 2,0.635 0.479,0.208 10 false R11
*a Component without harness connected
(Map Light Assembly (Radio and Display Receiver Assembly Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - R11-14 (SNS2) Always Below 1 Ω
B-2 - R11-5 (MCO-) Always Below 1 Ω
B-1 or R11-14 (SNS2) - R11-11 (GND) Always 10 kΩ or higher
B-2 or R11-5 (MCO-) - R11-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY