The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2782 | Power Source Control ECU Malfunction | Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the ignition switch is ON.)):
·
The steering lock motor activation command circuit has a short circuit. ·
The steering lock motor activation command circuit has an open circuit.
|
·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the ignition switch off. The steering unlocks when the ignition switch is turned to ACC or ON while carrying the key.) |
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. | Prohibits the hybrid control system from being started (the hybrid control system does not start). |
| DTC No. | Data List and Active Test |
|---|---|
| B2782 | - |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H52-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Move the shift lever to P and turn the ignition switch off.
Check the signal waveform according to the condition(s) in the table below.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
*b | Steering lock motor not operating |
| *c | Steering lock motor operating | *d | Waveform |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| H52-3 (IGE) - H52-1 (GND) | 2 V/DIV., 200 ms./DIV. | Steering lock motor not operating → Operating → Not operating | Pulse generation
(See waveform) |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.
To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform the DTC output confirmation operation.
Check if DTC B2782 is output.
| Result | Proceed to |
|---|---|
| DTC B2782 is not output. | A |
| DTC B2782 is output. | B |
A
B
Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H52-3 (IGE) - H48-25 (SLR+) | Always | Below 1 Ω |
| H52-3 (IGE) or H48-25 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG