Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Additional Key cannot be Registered  


DESCRIPTION

If additional registration is not possible, a malfunction of the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), power switch, No. 1 indoor electrical key antenna assembly (front floor), steering lock ECU (steering lock actuator or upper bracket assembly) or door control receiver is suspected.

CAUTION / NOTICE / HINT

NOTICE:
·

If registration of an electrical key transmitter sub-assembly cannot be performed, refer to Service Bulletin.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.



HINT:

When additional registration is not possible, freeze frame data may be stored in the certification ECU (smart key ECU assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CHECK FOR INTERMITTENT PROBLEMS


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
NOTICE:

If a malfunction occurs, do not remove/install the vehicle auxiliary battery before checking for DTCs.


OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (UNMATCHED VEHICLE-ID)

NG

2.READ VALUE USING GTS (UNMATCHED VEHICLE-ID)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unmatched Vehicle-ID Key No. (incorrect or correct) No or Yes No: Communication normal
Yes: Communication malfunction
The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
Other potential causes:
·

An electrical key transmitter sub-assembly from a different vehicle is being used.

·

A communication error due to wave interference.

·

The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unmatched Vehicle-ID
50003 125 20

Result:
Result Proceed to
"No" is displayed A
"Yes" is displayed B



A

3.CHECK ENTRY AND START SYSTEM (for Start Function)

B

5.REGISTRATION
3.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.


b.
B463968C06
0.573,0.229 0.813,0.229 0.813,0.229 0.969,0.667 false 1.25,1.813 1.458,1.813 1.458,1.813 1.698,1.573 false 0.417,0.146 0.729,0.344 0.313,0.198 10 false *1 1.083,1.729 1.396,1.927 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.



Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

4.CHECK STEERING LOCK FUNCTION

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

4.CHECK STEERING LOCK FUNCTION
a.

The ignition switch is ACC or ON.


b.

Check that the steering unlocks.

HINT:
·

When the ignition switch is turned to ACC or ON and the electrical key transmitter assembly and certification ECU (smart key ECU assembly) are verified, the steering is unlocked.


·

Check that the communication between the steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) is normal.



OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

5.REGISTRATION

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Hybrid Control System cannot Start))

5.REGISTRATION
a.

Using an unregistered electrical key transmitter sub-assembly, perform the additional registration procedure.

HINT:

Refer to Service Bulletin.


OK:

Additional registration can be completed.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (FIRST REGISTERED KEY WAS DEFECTIVE)

NG

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies.

HINT:

Refer to Service Bulletin.


OK:

All of the electrical key transmitter sub-assemblies could be registered to the new certification ECU (smart key ECU assembly) successfully.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG