Home › Engine / Hybrid System › 2GR-FKS (COOLING) › WATER PUMP
RM37A0E _51 Engine / Hybrid System _086855 2GR-FKS COOLING _0419159 WATER PUMP A

2GR-FKS COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A407190N01
2.865,0.667 3.094,0.927 0.229,0.26 10 true A 0.219,0.594 0.406,0.813 0.188,0.219 10 true A 0.208,1.771 0.438,1.979 0.229,0.208 10 true B 0.615,1.802 0.844,2.01 0.229,0.208 10 true B 1.479,1.906 1.708,2.115 0.229,0.208 10 true B 2.615,1.635 2.844,1.844 0.229,0.208 10 true B 3.135,1.198 3.365,1.406 0.229,0.208 10 true B 2.01,1.823 2.24,2.031 0.229,0.208 10 true C 2.208,1.563 2.438,1.771 0.229,0.208 10 true C 2.615,0.552 2.844,0.76 0.229,0.208 10 true C 2.604,0.073 2.833,0.281 0.229,0.208 10 true C 1.75,0.302 1.979,0.51 0.229,0.208 10 true C 1.271,0.542 1.5,0.75 0.229,0.208 10 true B 0.729,0.51 0.958,0.719 0.229,0.208 10 true C 1.042,1.74 1.271,1.948 0.229,0.208 10 true C

Install a new water pump gasket and the engine water pump assembly with the 15 bolts.

Torque:
Bolt (A) : 43 N*m (438 kgf*cm, 32 ft.*lbf)
Bolt (B) : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt (C) : 11 N*m (112 kgf*cm, 8 ft.*lbf)

Standard Length:
Item Length
Bolt (A) 60 mm (2.36 in.)
Bolt (B) 55 mm (2.17 in.)
Bolt (C) 22 mm (0.866 in.)


NOTICE:
·

Make sure that there is no oil on the threads of the bolts (A) and (B).

·

Do not start the engine for at least 1 hour after installation.




Hide 16173 2.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.
A478644C02
1.583,2.333 1.823,1.917 1.823,1.917 2.188,1.917 true 2.583,0.323 2.833,0.323 2.833,0.323 2.99,0.896 true 1.781,2.688 2.292,2.688 true 1.448,2.313 1.698,2.469 0.25,0.156 10 true *a 1.583,2.615 1.802,2.781 0.219,0.167 10 true *b 2.385,0.25 2.635,0.427 0.25,0.177 10 true *c
*a Protective Tape
*b Hold
*c Turn


Using a screwdriver or equivalent with its tip wrapped in protective tape, hold the water pump pulley.


c.

Fully tighten the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16604 3.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 2 idler pulley sub-assembly with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 16361A 4.INSTALL V-RIBBED BELT

Hide 16031 5.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY