Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419213 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.

HINT:

The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2782 Power Source Control ECU Malfunction Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the ignition switch is ON.)):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation: Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the ignition switch off. The steering unlocks when the ignition switch is turned to ACC or ON while carrying the key.)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2782 -

WIRING DIAGRAM

B463087E25
0.885,3.375 2.688,3.688 1.802,0.313 10 false : LIN Communication Line 5.542,2.635 7.052,2.99 1.51,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.552,2.469 6.177,2.75 0.625,0.281 10 false H48 5.99,0.344 6.573,0.552 0.583,0.208 10 false SLR+ 5.719,0.219 6.063,0.542 0.344,0.323 10 false 25 1.896,0.219 2.24,0.542 0.344,0.323 10 false 3 1.552,0.333 1.896,0.656 0.344,0.323 10 false IGE 1.5,2.052 1.844,2.375 0.344,0.323 10 false GND 1.896,1.938 2.24,2.26 0.344,0.323 10 false 1 0.115,2.5 1.781,2.906 1.667,0.406 10 false H52 0.094,2.667 2.76,3.198 2.667,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
B521840C42
1.5,1.042 1.927,1.281 0.427,0.24 0.896,1.719 1.219,1.719 1.219,1.719 1.219,2.427 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.583,1.073 1.969,1.26 0.385,0.188 10 false H52 0.542,1.625 0.979,1.854 0.438,0.229 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H52-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Move the shift lever to P and turn the ignition switch off.


c.

Check the signal waveform according to the condition(s) in the table below.

B573076C09
1.688,0.417 2.094,0.667 0.406,0.25 4,1.01 5.115,1.208 1.115,0.198 5,1.938 5.729,2.135 0.729,0.198 5.542,1.052 5.938,1.24 0.396,0.188 1.844,2.448 2.01,2.448 2.01,2.448 2.01,1.271 true 2.49,2.448 2.302,2.448 2.302,2.448 2.302,1.271 true 5.115,1.01 6.094,0.479 6.094,0.479 5.563,1.052 true 5.531,2.49 5.344,2.49 5.344,2.49 5.344,2.146 true 0.531,0.531 0.844,0.688 0.313,0.156 10 false *a 6.135,0.385 6.448,0.542 0.313,0.156 10 false *b 5.573,2.406 5.885,2.563 0.313,0.156 10 false *c 3.646,0.646 3.958,0.802 0.313,0.156 10 false *d 1.771,0.458 2.125,0.646 0.354,0.188 10 false H52 1.583,2.365 1.969,2.625 0.385,0.26 10 false IGE 2.531,2.375 2.917,2.635 0.385,0.26 10 false GND 6.156,1.969 6.542,2.229 0.385,0.26 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating *d Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition
H52-3 (IGE) - H52-1 (GND) 2 V/DIV., 200 ms./DIV. Steering lock motor not operating → Operating → Not operating Pulse generation
(See waveform)


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

3.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
3.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.

CAUTION:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B2782 is output.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2782 is not output. A
DTC B2782 is output. B



A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H52-3 (IGE) - H48-25 (SLR+) Always Below 1 Ω
H52-3 (IGE) or H48-25 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR