Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419213 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2285 Steering Lock Position Signal Circuit Malfunction The steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*)
·

LIN communication system

·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait at least 40 seconds with the ignition switch off (wait is the steering locked), then turn the ignition switch to ON (steering unlocked) and wait at least 40 seconds.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. The ECU does not send an engine start request.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2285
Power Source Control

Steering Unlock Switch


Entry&Start
·

Power Supply Short

·

Motor Driver Short

·

Lock Bar Stuck Error



WIRING DIAGRAM

B491204E18
1.406,0.438 1.719,0.635 0.313,0.198 10 false +B 1.875,0.927 2.49,1.125 0.615,0.198 10 false SLP1 2.344,0.927 2.5,1.125 0.156,0.198 10 false 4 0.521,1.802 2.51,2 1.99,0.198 10 false Unlock Sensor 0.385,2.219 0.844,2.417 0.458,0.198 10 false H52 0.385,2.385 3.073,2.917 2.688,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 5.958,0.302 6.271,0.5 0.313,0.198 10 false +B 5.688,0.927 6.156,1.135 0.469,0.208 10 false SLP 5.417,0.927 5.698,1.156 0.281,0.229 10 false 14 6.448,1.042 6.76,1.24 0.313,0.198 10 false IC 5.469,2.219 5.927,2.417 0.458,0.198 10 false H48 5.469,2.385 6.979,2.792 1.51,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.583,3.427 4.25,3.625 3.667,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:
·

If the steering cannot be unlocked, the ignition switch cannot be turned to ON and the engine cannot be started.

·

If LIN communication is not available, the steering cannot be locked or unlocked.



OK:

LIN communication system DTC B2785 is not output simultaneously.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)

NG

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) OFF or ON OFF: Steering locked
ON: Steering unlocked
·

When the shift lever is in P and the ignition switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned to ACC or ON, the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

3.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
3.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C342153C60
1.479,0.167 1.896,0.417 0.417,0.25 1.365,1.792 1.719,1.792 1.719,1.792 1.719,1.135 true 0.188,0.177 0.5,0.375 0.313,0.198 10 false *a 1.563,0.208 1.958,0.438 0.396,0.229 10 false H52 0.958,1.708 1.396,1.917 0.438,0.208 10 false SLP1
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H52-4 (SLP1) - Body ground Positive (+) tester probe → H52-4 (SLP1)
Negative (-) tester probe → Body ground
Steering locked → unlocked* 10 kΩ or higher → Below 1 Ω


HINT:
·

*: If any of the doors are opened with the shift lever in P and the ignition switch off, the steering will be locked. If the ignition switch is turned to ACC or ON with the electrical key transmitter sub-assembly in the cabin, the steering will be unlocked.

·

DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator or upper bracket assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator or upper bracket assembly) to the certification ECU (smart key ECU assembly) individually.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-14 (SLP) - H52-4 (SLP1) Always Below 1 Ω
H48-14 (SLP) or H52-4 (SLP1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR