Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › 2020.02–2021.10
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS ENGINE CONTROL  SFI SYSTEM  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction ECM Comes on DTC stored SAE Code: P2610

A404893E06
0.146,1.927 1.031,2.417 0.885,0.49 10 false from Auxiliary Battery 0.594,1.292 1.667,1.49 1.073,0.198 10 false MAIN 1.958,1.031 2.719,1.323 0.76,0.292 10 false IG2-MAIN 2.76,1.615 3.531,1.896 0.771,0.281 10 false IG2 NO. 1 1.479,2.031 4.875,2.385 3.396,0.354 10 false from Certification ECU (Smart Key ECU Assembly) 3.74,1.052 4.854,1.333 1.115,0.281 10 false ECU-IG2 NO. 1 4.313,0.729 4.917,1.031 0.604,0.302 10 false IGSW 5,1.125 5.698,1.573 0.698,0.448 10 false Soak Timer IC 4.531,2.896 4.833,3.188 0.302,0.292 10 false +B 5,2.802 5.635,3.271 0.635,0.469 10 false Power Source IC 1.229,3.594 2.396,3.885 1.167,0.292 10 false EFI-MAIN NO. 1 2.646,4.135 3.792,4.438 1.146,0.302 10 false EFI-MAIN NO. 1 4.333,3.708 4.875,3.958 0.542,0.25 10 false MREL 4.99,3.615 5.708,4.083 0.719,0.469 10 false Main Relay Control IC 5.594,4.323 6.052,4.594 0.458,0.271 10 false ECM

MONITOR DESCRIPTION

The ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and sets the DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

10.

Turn the ignition switch off and wait for at least 15 seconds.

11.

Turn the ignition switch to ON.

12.

Turn the GTS on.

13.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

14.

Start the engine.

15.

Stop the engine and leave the vehicle for 60 minutes or more.

16.

Turn the ignition switch to ON.

17.

Turn the GTS on.

18.

Enter the following menus: Powertrain / Engine / Trouble Codes.

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

21.

Input the DTC: P261029.

22.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>VEHICLE CONTROL HISTORY



HINT:
·

DTC P261029 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the Pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If no pending DTC is output, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END