Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS, A25B-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS, A25B-FXS ENGINE CONTROL  SFI SYSTEM  P052024  Engine Oil Pressure Sensor/Switch "A" Signal Stuck High  P05202A  Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range  


DESCRIPTION

Refer to DTC P052012.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>P052012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052024 Engine Oil Pressure Sensor/Switch "A" Signal Stuck High The oil pressure sensor output voltage is higher than the threshold value (1 trip detection logic).
·

Open or short in oil pressure sensor circuit

·

Oil pressure and temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0521
P05202A Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range The oil pressure sensor output voltage is the same value for a certain period of time (1 trip detection logic).
·

Open or short in oil pressure sensor circuit

·

Oil pressure and temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0521

Related Data List
DTC No. Data List
P052024
·

Engine Oil Temperature Sensor

·

Engine Oil Pressure


P05202A

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sensor. If any of the following are detected, the ECM will illuminate the MIL and store a DTC.

·

The oil pressure sensor output value differs from the specified value for a given engine speed (P052024).

·

The oil pressure sensor output voltage does not change for a certain period of time (P05202A).


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A331687E36
0.542,1.021 1.219,1.25 0.677,0.229 10 false 2500 rpm 0.229,2.156 1.156,2.667 0.927,0.51 10 false Ignition Switch ON 0.802,1.906 1.479,2.135 0.677,0.229 10 false Idling 6.281,3.344 6.635,3.625 0.354,0.281 10 false [C] 2.063,2.844 2.917,3.146 0.854,0.302 10 false Warming up 2.979,2.865 3.75,3.156 0.771,0.292 10 false 30 seconds 2.281,1.781 2.521,2 0.24,0.219 10 false [A] 3.146,1.385 3.385,1.604 0.24,0.219 10 false [B] 4.125,1.354 4.365,1.573 0.24,0.219 10 false [B] 5.146,1.375 5.385,1.594 0.24,0.219 10 false [B] 3.969,2.865 4.74,3.156 0.771,0.292 10 false 30 seconds 4.948,2.865 5.719,3.156 0.771,0.292 10 false 30 seconds

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [A].

10.

When the vehicle is stationery, gently depress the accelerator pedal until the engine speed increases to 2500 rpm for 30 seconds, then release the accelerator pedal to return to the idling speed [B].

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [B] after charge control has completed.


11.

Repeat step [B] 3 times or more.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P052024 or P05202A.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P052024 OR P05202A)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P052024 or P05202A is output A
DTC P052024 or P05202A and other DTCs are output B


HINT:

If any DTCs other than P052024 or P05202A are output, troubleshoot those DTCs first.




A

2.INSPECT OIL PRESSURE AND TEMPERATURE SENSOR

B

GO TO DTC CHART

2.INSPECT OIL PRESSURE AND TEMPERATURE SENSOR
a.

Read the value displayed on the GTS.

i.

Disconnect the oil pressure control valve assembly connector.


ii.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

iii.

Start the engine.


iv.

With the engine oil temperature at 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Engine Oil Temperature Sensor
Engine Oil Pressure
50003 372 211,261,103


b.

Read the oil pressure using an oil pressure gauge with adapter.


ii.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

iii.

Start the engine.


iv.

Maintain "Coolant Temperature" at 90 to 95°C (194 to 203°F) for 3 minutes, and then read the oil pressure gauge value at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Coolant Temperature
50003 372 211,205
HINT:
·

When the engine oil pressure and temperature sensor is removed, the engine oil temperature cannot be checked, so refer to "Coolant Temperature".

·

Race the engine as necessary to maintain "Coolant Temperature" at 90 to 95°C (194 to 203°F).

·

If maintained for 3 minutes or more, the engine oil temperature may exceed 85°C (185°F).





c.

Compare the Data List value and the oil pressure gauge reading.

OK:

Data List value and gauge reading are within +/-50 kPa (7.3 psi) of each other


HINT:

Be sure to clear the DTCs after reinstalling the oil pressure and temperature sensor or reconnecting the oil pressure and temperature sensor or oil pressure control valve assembly connector, as DTCs may be stored.



Result:
Proceed to
OK
NG



OK

NG