Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM37A0E _52 Drivetrain _086859 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0419507 AUTOMATIC TRANSAXLE SYSTEM D

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD (EUROPEAN SPEC)


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, an OBD scan tool (complying with ISO 15765-4) must be connected to the vehicle. Various data output from the vehicle ECM can then be read.


b.
F102324

Euro-OBD regulations require that the vehicle on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

1.

The emission control system/components

2.

The powertrain control components (which affect vehicle emissions)

3.

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory.

If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs will remain recorded in the ECM memory.


c.

To check for DTCs, connect the GTS to the Data Link Connector 3 (DLC3) of the vehicle. The GTS displays DTCs, freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared with the GTS.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR



NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used to increase the system's ability to detect malfunctions, including intermittent problems, when simulating malfunction symptoms (GTS only).



2 TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next driving cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E24
0.354,1.74 2.792,1.99 2.438,0.25 10 false Freeze frame data which can be read 0.698,0.708 1.323,0.906 0.625,0.198 10 false 0.5 sec. 1.333,0.708 1.958,0.906 0.625,0.198 10 false 0.5 sec. 1.99,0.708 2.615,0.906 0.625,0.198 10 false 0.5 sec. 1.823,0.104 2.875,0.396 1.052,0.292 10 false DTC was stored

The GTS records freeze frame data in 5 different instances: 1) 3 times before a DTC is stored, 2) once when a DTC is stored, and 3) once after a DTC is stored. These sets of data can be used to simulate the vehicle condition around the time when the malfunction occurred. The data may help in diagnosing the malfunction, or in judging if the DTC was stored due to a temporary malfunction.



CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK BATTERY VOLTAGE


Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery.


CHECK MIL


a.

Check that the MIL illuminates when the ignition switch is turned to ON (engine not started).


b.

The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction in the system.

HINT:

If the MIL is not illuminated when the ignition switch is turned to ON, check the MIL circuit.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>MIL Circuit