The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the ECM.
Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (NC) signals, the ECM controls engine torque and shift timing. Based on the input shaft rotation speed and the engine speed signal, lock-up control is performed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071512 | Input/Turbine Speed Sensor "A" Circuit Short to Battery | All of the following conditions are met (1-trip detection logic):
·
The battery voltage is 8 V or more. ·
The ignition switch is ON. ·
The starter is off. ·
Transmission revolution sensor (NT) input voltage is more than 1.9 V for 4.5 seconds. |
·
Transmission revolution sensor (NT) ·
Transmission wire ·
Harness and connector ·
ECM |
Comes on | DTC stored | SAE Code:
P07C0 |
| P071514 | Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open | All of the following conditions are met (1-trip detection logic):
·
The battery voltage is 8 V or more. ·
The ignition switch is ON. ·
The starter is off. ·
Transmission revolution sensor (NT) input voltage is less than 0.1 V for 4.5 seconds or more. |
·
Transmission revolution sensor (NT) ·
Transmission wire ·
Harness and connector ·
ECM |
Comes on | DTC stored | SAE Code:
P07BF |
| P071531 | Input/Turbine Speed Sensor "A" No Signal | All of the following conditions are met (1-trip detection logic):
·
The battery voltage is 8 V or more. ·
The park/neutral position switch D input signal is ON. ·
The speed indicated by transmission revolution sensor (NC) is 490 rpm or more. ·
The vehicle speed is 24 km/h (15 mph) or more. ·
The vehicle is being driven in 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear. ·
The speed indicated by transmission revolution sensor (NT) is less than 300 rpm for 5 seconds or more. |
·
Transmission revolution sensor (NT) ·
Transmission wire ·
Harness and connector ·
ECM |
Comes on | DTC stored | SAE Code:
P0717 |
The NT terminal of the ECM detects a pulse signal from the transmission revolution sensor (NT) (input RPM). The ECM calculates gear shifts by comparing input signals of the transmission revolution sensor (NT) with the transmission revolution sensor (NC).
While the vehicle is being driven in 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm* when the vehicle speed is 24 km/h (15 mph) or more, the ECM interprets this as a malfunction, illuminates the MIL and stores a DTC.
*: Pulse is not output or is irregularly output.
When performing the D Position Shift Test inspection in Road Test, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Shift Test inspection in Road Test.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P071512, P071514 or P071531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Strictly observe posted speed, limits, traffic laws and road conditions.
Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.
Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.
Do not operate the GTS while driving the vehicle.
Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NT Sensor Speed | Input shaft speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up engine) ·
Nearly equal to engine speed: Lock-up off (idling with shift lever in N) |
Data is displayed in increments of 50 rpm |
| Tester Display |
|---|
| NT Sensor Speed |
NT Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.
NT Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NT Sensor Speed | Input shaft speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up engine) ·
Nearly equal to engine speed: Lock-up off (idling with shift lever in N) |
Data is displayed in increments of 50 rpm |
| NT Sensor Voltage | NT sensor voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V: Engine idling | - |
| Tester Display |
|---|
| NT Sensor Speed |
| NT Sensor Voltage |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
B
| *a | Front view of wire harness connector
(to Transmission Wire) |
Disconnect the C51 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C51-11 (NTO) - Body ground | Always | 99 to 101 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C51-12 (NTB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Transmission Wire |
| *a | Transmission Revolution Sensor (NT) Side |
| *b | Wire Harness Connector Side |
Disconnect the transmission revolution sensor (NT) connector.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE>REMOVAL
Disconnect the C51 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (transmission revolution sensor (NT) side) - 12 (NTB) (wire harness connector side) | Always | Below 1 Ω |
| 2 (transmission revolution sensor (NT) side) - 11 (NTO) (wire harness connector side) | Always | Below 1 Ω |
| 1 (transmission revolution sensor (NT) side) or 12 (NTB) (wire harness connector side) - Body ground and other terminals | Always | 10 kΩ or higher |
| 2 (transmission revolution sensor (NT) side) or 11 (NTO) (wire harness connector side) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C51 transmission wire connector.
Disconnect the C54 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C51-12 (NTB) - C54-75 (NTB) | Always | Below 1 Ω |
| C51-11 (NTO) - C54-74 (NTO) | Always | Below 1 Ω |
| C51-12 (NTB) or C54-75 (NTB) - Body ground and other terminals | Always | 10 kΩ or higher |
| C51-11 (NTO) or C54-74 (NTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION