PARKING ASSIST ECU
Disconnect the H20 parking assist ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H20-1 (+B) - H20-4 (GND1) | Power source signal | Always*1 | 11 to 14 V |
| Ignition switch off*2 | |||
| H20-2 (ACC) - H20-4 (GND1) | ACC power source signal | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| H20-3 (IG) - H20-4 (GND1) | IG power source signal | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| H20-4 (GND1) - Body ground | Ground | Always | Below 1 Ω |
*1: for Gasoline Model
*2: for HV Model
Reconnect the H20 parking assist ECU connector.
Measure the voltage, resistance and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H19-6 (RSW+) - H20-4 (GND1) | Terminal required by law | Panoramic image being displayed | 0 to 2 V |
| Panoramic image not being displayed | 5.5 to 7.05 V | ||
| H19-7 (NS+) - H19-24 (NS-) | Video signal | Ignition switch ON and panoramic image being displayed | Pulse generation (See waveform 3) |
| H19-8 (NSG) - Body ground | Shield ground | Always | 10 kΩ or higher |
| H19-10 (LCV+) - H19-35 (LGND) | Side television camera assembly LH display signal input | Ignition switch ON with the camera lens of the side television camera assembly LH not covered, displaying the panoramic image | Pulse generation (See waveform 1) |
| Ignition switch ON with the camera lens of the side television camera assembly LH covered, blacking out the panoramic image | Pulse generation (See waveform 2) | ||
| H19-11 (SGND) - Body ground | Shielded - Body ground | Always | Below 1 Ω |
| H19-12 (LCB+) - H19-35 (LGND) | Power source to side television camera assembly LH | Ignition switch ON | 5.5 to 7.05 V |
| H19-13 (BCV-) - H20-4 (GND1) | Front television camera assembly ground | Always | Below 1 Ω |
| H19-14 (SGND) - Body ground | Shielded - Body ground | Always | Below 1 Ω |
| H19-15 (BCB+) - H19-37 (BGND) | Power source to front television camera assembly | Ignition switch ON | 5.5 to 7.05 V |
| H19-16 (RCV-) - H20-4 (GND1) | Side television camera assembly RH ground | Always | Below 1 Ω |
| H19-17 (RGND) - H20-4 (GND1) | Side television camera assembly RH ground | Always | Below 1 Ω |
| H19-24 (NS-) - H20-4 (GND1) | Ground | Always | Below 1 Ω |
| H19-29 (CV+) - H19-32 (CGND) | Rear television camera assembly display signal input | Ignition switch ON with the camera lens of the rear television camera assembly not covered, displaying the panoramic image | Pulse generation (See waveform 1) |
| Ignition switch ON with the camera lens of the rear television camera assembly covered, blacking out the panoramic image | Pulse generation (See waveform 2) | ||
| H19-30 (CV-) - H20-4 (GND1) | Rear television camera assembly ground | Always | Below 1 Ω |
| H19-31 (SGND) - Body ground | Shielded - Body ground | Always | Below 1 Ω |
| H19-32 (CGND) - Body ground | Rear television camera assembly ground (shield) | Always | Below 1 Ω |
| H19-33 (CB+) - H19-32 (CGND) | Power source to rear television camera assembly | Ignition switch ON | 5.5 to 7.05 V |
| H19-34 (LCV-) - H20-4 (GND1) | Side television camera assembly LH ground | Always | Below 1 Ω |
| H19-35 (LGND) - H20-4 (GND1) | Side television camera assembly LH ground | Always | Below 1 Ω |
| H19-36 (BCV+) - H19-37 (BGND) | Front television camera assembly display signal input | Ignition switch ON with the camera lens of the front television camera assembly not covered, displaying the panoramic image | Pulse generation (See waveform 1) |
| Ignition switch ON with the camera lens of the front television camera assembly covered, blacking out the panoramic image | Pulse generation (See waveform 2) | ||
| H19-37 (BGND) - H20-4 (GND1) | Front television camera assembly ground | Always | Below 1 Ω |
| H19-38 (RCV+) - H19-17 (RGND) | Side television camera assembly RH display signal input | Ignition switch ON with the camera lens of the side television camera assembly RH not covered, displaying the panoramic image | Pulse generation (See waveform 1) |
| Ignition switch ON with the camera lens of the side television camera assembly RH covered, blacking out the panoramic image | Pulse generation (See waveform 2) | ||
| H19-39 (SGND) - Body ground | Shielded - Body ground | Always | Below 1 Ω |
| H19-40 (RCB+) - H19-17 (RGND) | Power source to side television camera assembly RH | Ignition switch ON | 5.5 to 7.05 V |
| H20-15 (BLSW) - Body ground | Panoramic view monitor switch (front wide view switch) signal | Ignition switch ON, panoramic view monitor switch (front wide view switch) not pushed | 5.5 to 6.5 V |
| Ignition switch ON, panoramic view monitor switch (front wide view switch) pushed | Below 1 V | ||
| H20-11 (CANH) | CAN communication line | - | - |
| H20-12 (CANL) | CAN communication line | - | - |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
Reference (Oscilloscope waveform):
A waterproof connector is used for the rear television camera assembly, front television camera assembly, side television camera assembly LH and side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
Waveform 1 (camera lens is not covered, displaying an image)
| Item | Content |
|---|---|
| Measurement terminal | ·
H19-29 (CV+) - H19-32 (CGND) ·
H19-10 (LCV+) - H19-35 (LGND) ·
H19-36 (BCV+) - H19-37 (BGND) ·
H19-38 (RCV+) - H19-17 (RGND) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Panoramic view monitor system operating |
The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.
The video waveform is constantly output when the ignition switch is turned to ACC.
Waveform 2 (camera lens is covered, blacking out the screen)
| Item | Content |
|---|---|
| Measurement terminal | ·
H19-29 (CV+) - H19-32 (CGND) ·
H19-10 (LCV+) - H19-35 (LGND) ·
H19-36 (BCV+) - H19-37 (BGND) ·
H19-38 (RCV+) - H19-17 (RGND) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Panoramic view monitor system operating |
The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.
The video waveform is constantly output when the ignition switch is turned to ACC.
| *a | Waveform 3 (camera lens is not covered, displaying an image) |
| *b | Synchronization Signal |
| *c | Video Waveform |
Waveform 3
| Item | Content |
|---|---|
| Measurement terminal | H19-7 (NS+) - H19-24 (NS-) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Panoramic image being displayed |
The video waveform changes according to the image sent by the parking assist ECU.
RADIO AND DISPLAY RECEIVER ASSEMBLY