Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1614  ECU Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges that there is an internal malfunction as a result of its self check.

HINT:

The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1614 ECU Malfunction
·

Power source malfunction

·

Main CPU start malfunction

·

Main CPU reset detected

·

Main CPU regular monitoring malfunction

·

CAN CPU start malfunction

·

System standby malfunction

·

Main EEPROM malfunction

·

Sub EEPROM malfunction

·

Image ASIC RAM malfunction

·

ASIC status malfunction

·

ECU internal display line malfunction


Parking assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.READ VALUE USING GTS (PARKING ASSIST ECU STATUS)
a.

Use the Data List to check if the parking assist ECU status is functioning properly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Circumference Monitoring Camera Control Module > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
HV/EV/ENG Data Check Verification of the HV/ENG data OK/NG OK: Data verification normal
NG: Data verification abnormal
-
2WD/4WD Data Check Verification of the 2WD/4WD data OK/NG OK: Data verification normal
NG: Data verification abnormal
-
Main CPU Forced Termination Detection Record A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the ignition switch off and a forced end was applied No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Abnormal Response Record A history item indicating that the main CPU became unresponsive in normal status No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Abnormal Reset Record A history item indicating that the main CPU was reset, although the ignition switch was not turned off in normal status No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Image Processing IC Written Protect Record A history item indicating that the image processing IC memory was write protected No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Image Processing IC Initialized Malfunction Record A history item indicating that the image processing IC memory was not initialized No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main EEPROM Access Status Main EEPROM access status Normal/Abnormal Normal: Parking assist ECU is normal
Abnormal: Parking assist ECU is abnormal
-
Sub EEPROM Access Status Sub-EEPROM access status Normal/Abnormal Normal: Parking assist ECU is normal
Abnormal: Parking assist ECU is abnormal
-
System Power Supply Voltage Malfunction Record A history item indicating an abnormal generated-voltage value from the system power source No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Starting Malfunction Record A history item indicating that the main CPU did not start No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
CAN CPU Boot Malfunction Record A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Visual Display Line Status Displays the status of the video signals displayed on the multi-display OK/NG OK: GVIF cable is normal
NG: GVIF cable is abnormal
-
Wheel Speed Sensor (4wheel) Reception state of the vehicle speed signal from the skid control ECU*1, No. 2 skid control ECU*2 OK/NG OK: Speed signal received
NG: Speed signal not received
-
Continuous Bus Off Continuous bus off status (Global) Not Detected/Detected Not detected: Communication condition available
Detected: Communication condition not available
-
Sending CAN Message Communication condition from parking assist ECU (Global) OK/NG OK: Communication condition available
NG: Communication condition not available
-
Camera Changing SW Signal Status Signal status at the BLSW terminal (switch camera signal) ON/OFF ON: Panoramic view monitor main switch on
OFF: Panoramic view monitor main switch off
-
Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
NG: Rear television camera assembly or parking assist ECU is abnormal
-
Image Adjustment Status Status of the image adjustment status Incomplete/Processing/Complete Incomplete: Image adjustment incomplete
Processing: Image adjustment in processing
Complete: Image adjustment completed
-
Number of DTC Number of DTCs (past and present) Min: 0, Max: 255 Number of DTCs will be displayed -

*1: for Gasoline Model

*2: for HV Model


Chassis > Circumference Monitoring Camera Control Module > Data List
Tester Display
HV/EV/ENG Data Check
2WD/4WD Data Check
Main CPU Forced Termination Detection Record
Main CPU Abnormal Response Record
Main CPU Abnormal Reset Record
Image Processing IC Written Protect Record
Image Processing IC Initialized Malfunction Record
Main EEPROM Access Status
Sub EEPROM Access Status
System Power Supply Voltage Malfunction Record
Main CPU Starting Malfunction Record
CAN CPU Boot Malfunction Record
Visual Display Line Status
Wheel Speed Sensor (4wheel)
Continuous Bus Off
Sending CAN Message
Camera Changing SW Signal Status
Back Camera Availability Consistency
Image Adjustment Status
Number of DTC
50003 353 8,9,10,11,12,13,14,15,16,17,18,19,38,20,62,63,23,53,41,37

Result:
Result Proceed to
OK is displayed for all items A
NG is displayed B



A

B

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1614 is not output.


Result:
Proceed to
OK
NG


HINT:
·

If DTC C1614 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.

·

If DTC C1614 is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.

·

If DTC C1614 is output frequently, replace the parking assist ECU even though the DTC is not output when rechecking for DTCs.





OK

END

NG