Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P066014  Intake Manifold Tuning Valve Control Circuit Short to Ground or Open  


DESCRIPTION

ACIS (Acoustic Control Induction System) controls the opening and closing the intake air control valve sub-assembly built into the intake air surge tank assembly to increase the intake efficiency according to the engine load.

When the engine speed is between 0 and 4300 rpm and the throttle valve opening angle is 30° or more, the ECM activates the No. 1 vacuum switching valve assembly (for ACIS) which then applies vacuum from the vacuum pump assembly to the diaphragm actuator sub-assembly and closes the intake air control valve sub-assembly.

When the engine speed and/or throttle valve opening angle are not as specified above, the ECM deactivates the No. 1 vacuum switching valve assembly (for ACIS), causing the intake air control valve sub-assembly to open.

A373331E05
0.615,2.208 1.01,0.802 1.01,0.802 1.125,0.802 false 1.344,1.656 1.344,1.125 1.344,1.125 1.458,1.125 false 4.74,3.5 4.719,2.219 4.719,2.219 4.875,2.229 false 5.229,6.281 5.104,6.281 5.104,6.281 5.094,5.188 false 2.813,3.135 2.635,3.135 2.635,3.135 1.688,2.74 true 0.625,3.688 0.625,3.531 0.625,3.531 1.125,2.854 false 0.646,6.698 0.958,5.313 0.958,5.313 1.083,5.313 false 1.344,6.156 1.333,5.771 1.333,5.771 1.438,5.771 false 3.198,2.396 3.51,1.573 3.51,1.573 3.625,1.573 false 3.198,6.885 3.26,5.823 3.26,5.823 3.365,5.823 false 0.719,8.021 0.719,7.885 0.719,7.885 1.188,7.354 false 2.865,7.75 2.698,7.74 2.698,7.74 1.677,7.271 true 0.031,0.271 0.938,0.542 0.906,0.271 10 false Engine Speed 1.219,0.24 3.042,0.573 1.823,0.333 10 false Throttle Valve Opening Angle 0.344,1.365 0.719,1.573 0.375,0.208 10 false ECM 1.156,0.656 3.052,1.021 1.896,0.365 10 false No. 1 Vacuum Switching Valve Assembly 1.5,1.042 3.073,1.354 1.573,0.313 10 false Vacuum Pump Assembly 2.906,3.073 4.219,3.479 1.313,0.406 10 false Intake Air Control Valve Assembly 3.625,3.729 4.573,4.125 0.948,0.396 10 false Throttle Valve Opening Angle 4.302,4.25 4.625,4.49 0.323,0.24 10 false 30° 4.969,2.146 6.74,2.927 1.771,0.781 10 false Intake Air Control Valve Assembly Closed (Vacuum Switching Valve: on) 4.479,5.333 4.917,5.552 0.438,0.219 10 false 0 rpm 6.083,5.344 6.74,5.635 0.656,0.292 10 false 4300 rpm 6.156,5.667 7.115,5.948 0.958,0.281 10 false Engine Speed 5.271,6.188 7.042,7.073 1.771,0.885 10 false Intake Air Control Valve Assembly Open (Vacuum Switching Valve: off) 2.406,3.542 2.563,3.74 0.156,0.198 10 false 1 1.896,3.552 2.052,3.75 0.156,0.198 10 false 3 1.365,3.531 1.521,3.729 0.156,0.198 10 false 5 2.385,1.823 2.563,1.979 0.177,0.156 10 false 2 1.875,1.823 2.031,1.99 0.156,0.167 10 false 4 1.365,1.854 1.521,2.031 0.156,0.177 10 false 6 0.052,3.708 1.302,4.208 1.25,0.5 10 false Diaphragm Actuator Sub-assembly 0.052,4.75 1,5.031 0.948,0.281 10 false Engine Speed 1.177,4.76 3.01,5.073 1.833,0.313 10 false Throttle Valve Opening Angle 0.313,5.865 0.698,6.094 0.385,0.229 10 false ECM 1.156,5.229 3.104,5.635 1.948,0.406 10 false No. 1 Vacuum Switching Valve Assembly 1.479,5.688 3.115,6 1.635,0.313 10 false Vacuum Pump Assembly 3.688,1.5 5.229,1.833 1.542,0.333 10 false Throttle Position Sensor 3.417,5.76 4.979,6.021 1.563,0.26 10 false Throttle Position Sensor 0.031,8.042 1.292,8.521 1.26,0.479 10 false Diaphragm Actuator Sub-assembly 1.385,8.052 1.542,8.25 0.156,0.198 10 false 5 1.896,8.052 2.052,8.25 0.156,0.198 10 false 3 2.417,8.052 2.573,8.25 0.156,0.198 10 false 1 2.375,6.333 2.531,6.5 0.156,0.167 10 false 2 1.875,6.333 2.052,6.5 0.177,0.167 10 false 4 1.354,6.354 1.51,6.521 0.156,0.167 10 false 6 2.927,7.656 5.51,7.938 2.583,0.281 10 false Intake Air Control Valve Assembly 0.625,6.948 1.125,7.146 0.5,0.198 10 false Suction

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P066014 Intake Manifold Tuning Valve Control Circuit Short to Ground or Open The following conditions are met simultaneously for 3 seconds or more (2 trip detection logic):
1.

No. 1 vacuum switching valve assembly is OFF.

2.

The target control signal and actual control signal do not match.


·

Open or short in No. 1 vacuum switching valve assembly (for ACIS) circuit

·

No. 1 vacuum switching valve assembly (for ACIS)

·

ECM


Comes on DTC stored SAE Code: P0660

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 5 seconds.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P066014.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A410582E15
6.104,3.896 6.563,4.146 0.458,0.25 10 false ECM 5.667,3.323 6.125,3.573 0.458,0.25 10 false MREL 5.333,3.427 5.792,3.677 0.458,0.25 10 false A28 5.375,3.25 5.833,3.5 0.458,0.25 10 false 46 5.323,1.188 5.781,1.438 0.458,0.25 10 false C54 5.052,1.083 5.51,1.333 0.458,0.25 10 false 1 5.375,0.99 5.833,1.24 0.458,0.25 10 false 66 5.667,1.188 6.125,1.438 0.458,0.25 10 false ACIS 4.635,1.073 5.094,1.323 0.458,0.25 10 false ACIS 3.969,1.073 4.427,1.323 0.458,0.25 10 false +B 3.781,1.073 4.24,1.323 0.458,0.25 10 false 2 2.75,1.323 3.583,1.667 0.833,0.344 10 false EFI NO. 4 3.635,1.479 4.469,1.823 0.833,0.344 10 false C29 3.646,1.646 5.542,2.25 1.896,0.604 10 false No. 1 Vacuum Switching Valve Assembly (for ACIS) 1.594,1.552 2.052,1.802 0.458,0.25 10 false 1 2.281,1.552 2.74,1.802 0.458,0.25 10 false 2 2.271,1.073 2.729,1.323 0.458,0.25 10 false 5 1.583,1.073 2.042,1.323 0.458,0.25 10 false 3 1.677,1.979 2.573,2.208 0.896,0.229 10 false EFI-MAIN 0.469,1.719 1.198,1.969 0.729,0.25 10 false EFI-MAIN 0.469,2.625 1.729,2.958 1.26,0.333 10 false FL MAIN 0.615,3.365 1.875,3.698 1.26,0.333 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.

Start the engine.


b.

According to the display on the GTS, perform the Active Test to operate the No. 1 vacuum switching valve assembly (for ACIS) and check for the operating sound of the intake air control valve in the intake air surge tank assembly.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Intake Control
50004 372 47
OK:

Operating noise can be heard.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)
2.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS))

NG

REPLACE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS))
A373425C16
0.5,1.177 0.823,1.417 0.323,0.24 2.219,1.792 1.896,1.448 false 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 0.531,1.208 0.99,1.406 0.458,0.198 10 false C29 2.188,1.844 2.646,2.042 0.458,0.198 10 false +B
*a Front view of wire harness connector
(to No. 1 Vacuum Switching Valve Assembly (for ACIS))


a.

Disconnect the No. 1 vacuum switching valve assembly (for ACIS) connector.


b.

Turn the ignition switch to ON


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C29-2 (+B) - Body ground Ignition switch to ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN RELAY - NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS))

4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS) - ECM)
a.

Disconnect the No. 1 vacuum switching valve assembly (for ACIS) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-1 (ACIS) - C54-66 (ACIS) Always Below 1 Ω
C29-1 (ACIS) or C54-66 (ACIS) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR