Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A408632E03
0.177,1.927 1.115,2.26 0.938,0.333 10 false from Battery 0.615,1.292 1.688,1.49 1.073,0.198 10 false FL MAIN 1.781,1.021 2.573,1.333 0.792,0.313 10 false IG2-MAIN 2.771,1.604 3.583,1.979 0.813,0.375 10 false IG2 NO. 1 3.844,1.052 4.448,1.573 0.604,0.521 10 false ECU-IG2 NO. 1 4.323,0.76 4.938,0.958 0.615,0.198 10 false IGSW 5,1.115 5.729,1.49 0.729,0.375 10 false Soak Timer IC 5.042,2.792 5.708,3.146 0.667,0.354 10 false Power Source IC 4.51,2.875 4.802,3.135 0.292,0.26 10 false +B 4.99,3.604 5.719,4.01 0.729,0.406 10 false Main Relay Control IC 4.344,3.698 4.958,3.896 0.615,0.198 10 false MREL 2.792,4.167 3.635,4.438 0.844,0.271 10 false EFI-MAIN 1.792,3.573 2.604,3.844 0.813,0.271 10 false EFI-MAIN 2.854,2.031 4.677,2.521 1.823,0.49 10 false from Certification ECU (Smart Key ECU Assembly) 5.531,4.323 5.99,4.521 0.458,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored SAE Code: P2610

MONITOR DESCRIPTION

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and warm it up.

7.

Turn the ignition switch off and wait for at least 15 seconds.

8.

Turn the ignition switch to ON.

9.

Turn the GTS on.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P261029.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P261029 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

c.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END