The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
63218G
1.REMOVE SLIDING ROOF SIDE GARNISH LH
Fully open the sunshade trim sub-assembly.
Disengage the claw to remove the sliding roof side garnish LH.
63217G
2.REMOVE SLIDING ROOF SIDE GARNISH RH
Use the same procedure as for the LH side.
63201G
3.REMOVE NO. 1 SLIDING ROOF GLASS SUB-ASSEMBLY
Open the No. 1 sliding roof glass sub-assembly to a position where the 2 screws (A) can be removed.
Using a T25 "TORX" socket wrench, remove the 2 screws (A).
Fully close the No. 1 sliding roof glass sub-assembly.
Using a T25 "TORX" socket wrench, remove the 4 screws (B) and No. 1 sliding roof glass sub-assembly.
To prevent the No. 1 sliding roof glass sub-assembly and sliding roof drive gear assembly from being displaced, fully close the No. 1 sliding roof glass sub-assembly, and then remove the No. 1 sliding roof glass sub-assembly.
63201G
4.REMOVE NO. 2 SLIDING ROOF GLASS SUB-ASSEMBLY
Disconnect the sliding roof weatherstrip from the No. 2 sliding roof glass sub-assembly.
Using a T25 "TORX" socket wrench, remove the 4 screws and No. 2 sliding roof glass sub-assembly.
62180A
5.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH
62170A
6.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH
Use the same procedure as for the LH side.
7.DISCONNECT SLIDING ROOF DRAIN HOSE
for Clamp Type:
Disengage the claw and disconnect the sliding roof drain hose.
Use the same procedure for the other 3 sliding roof drain hoses.
for Clip Type:
Expand the clip and disconnect the sliding roof drain hose.
Use the same procedure for the other 3 sliding roof drain hoses.
63242A
8.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH
Remove the 2 bolts and front sliding roof housing mounting bracket LH.
Use the same procedure for the front side and rear side.
63241A
9.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH
Use the same procedure as for the LH side.
63244C
10.REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH
Remove the 11 bolts and center sliding roof housing mounting bracket LH.
63243C
11.REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH
Use the same procedure as for the LH side.
63246D
12.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH
Remove the 2 bolts and rear sliding roof housing mounting bracket LH.
63245D
13.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH
Use the same procedure as for the LH side.
14.REMOVE SLIDING ROOF HOUSING ASSEMBLY
Remove the 8 nuts and sliding roof housing assembly.