Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0421224 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2.REMOVE ROOF HEADLINING ASSEMBLY

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

for A25A-FXS, A25B-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 62180A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



d.
B566183

Disengage the 4 clamps to disconnect the airbag wire harness.


e.

Using needle-nose pliers, remove the 8 pins from the 8 clips (A).

B566184C01
2.563,1.865 2.813,1.865 true 3.448,1.865 3.698,1.865 false 5.042,2.479 5.292,2.479 5.292,2.479 5.458,2.25 true 6.667,0.354 6.438,0.354 6.438,0.354 6.438,1.104 true 2.823,1.781 3.031,1.958 0.208,0.177 10 false *1 3.719,1.792 3.927,1.969 0.208,0.177 10 false *1 5.833,0.479 6.042,0.646 0.208,0.167 10 true *b 1.885,1.51 2.094,1.677 0.208,0.167 10 false *a 6.698,0.281 6.906,0.448 0.208,0.167 10 true *c 4.885,2.406 5.094,2.583 0.208,0.177 10 false *2 4.146,0.854 4.354,1.021 0.208,0.167 10 true *b
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Spacer Location - -
V113147

Remove in this Direction - -



f.

Using 2 screwdrivers, disengage the 2 claws of each clip (A) and separate the 8 clips (A) from the vehicle body as shown in the illustration.

HINT:

Separate the 8 clips (A) and curtain shield airbag assembly from the vehicle body as a unit.



g.

Disengage the 2 clips (B).


h.

While holding the curtain shield airbag assembly, remove the 5 bolts and curtain shield airbag assembly.


i.

Remove the 8 clips (A) and the spacer from the curtain shield airbag assembly.