Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Moon Roof)
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0419685 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SLIDING ROOF HOUSING ASSEMBLY

a.

Loosen the 10 bolts from the brackets of the sliding roof housing assembly.


b.

Temporarily install the sliding roof housing assembly with the 6 nuts and 10 bolts.

B565140C02
4.417,1.969 4.26,1.771 true 2.458,0.802 2.365,0.396 true 1.25,0.802 1.719,1.063 true 3.375,2.354 3.667,2.188 true 1.219,1.729 1.51,1.563 true 2.177,2.271 2.469,2.104 true 2.531,0.854 2.646,1.021 0.115,0.167 10 true 1 4.406,2.052 4.521,2.219 0.115,0.167 10 true 2 1.052,0.688 1.25,0.875 0.198,0.188 10 true *b 0.99,1.646 1.208,1.833 0.219,0.188 10 true *c 1.948,2.177 2.167,2.365 0.219,0.188 10 true *c 3.156,2.26 3.354,2.448 0.198,0.188 10 true *b 4.104,1.594 4.302,1.781 0.198,0.188 10 true *a 2.26,0.198 2.458,0.385 0.198,0.188 10 true *a
*a Nut (A) *b Nut (B)
*c Nut (C) - -



c.

Tighten the 2 nuts (A).

HINT:

Tighten the 2 nuts (A) in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Tighten the 4 nuts.

Torque:
Nut (B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut (C) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Tighten the 10 bolts (A).

B565154C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Bolt (C) - -


Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


f.

Tighten the 4 bolts (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Tighten the 6 bolts (C) to install the sliding roof housing assembly.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)


Hide 86291 2.INSTALL TELEVISION BRACKET (w/ Rear Seat Entertainment System)

a.

Engage the 2 guides and clip.


b.

Install the television bracket with the 4 bolts.


Hide 3.CONNECT SLIDING ROOF DRAIN HOSE

a.
B565136C01
2.635,0.531 3,0.344 true 2.146,0.906 2.344,0.708 true 3,0.25 3.313,0.406 0.313,0.156 10 false *a 2.021,0.927 2.333,1.083 0.313,0.156 10 false *b
*a Clamp
*b Marking


for Clamp Type:

i.

Connect the sliding roof drain hose.

HINT:

Slide the hose to the base of the drain pipe.



ii.

Engage the claw to secure the sliding roof drain hose.

HINT:
·

Make sure that the clamp is on the marking or between the marking and hose end.

·

Use the same procedure for the other 3 sliding roof drain hoses.





b.
B565139C01
0.542,1.833 0.813,1.635 true 1.01,1.49 1.198,1.219 true 0.375,1.74 0.688,1.896 0.313,0.156 10 false *a 1.24,1.115 1.552,1.271 0.313,0.156 10 false *b 0.573,4.302 0.885,4.458 0.313,0.156 10 false *c 2.521,2.427 2.833,2.583 0.313,0.156 10 false *d
*a Clip
*b Marking
*c Front Side
*d Outside


for Clip Type:

i.

Expand the clip and connect the sliding roof drain hose.

HINT:

Slide the hose to the base of the drain pipe.



ii.

Release the clip to secure the sliding roof drain hose.

NOTICE:

The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing assembly when installing the sliding roof drain hoses.


HINT:
·

Make sure that the clip is on the marking or between the marking and hose end.

·

Use the same procedure for the other 3 sliding roof drain hoses.





Hide 62180A 4.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63201G 6.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

B565155N01
1.583,1.51 1.74,1.708 0.156,0.198 10 true A 6.125,1.063 6.281,1.26 0.156,0.198 10 false a 1.833,1.521 1.99,1.719 0.156,0.198 10 true A 2.177,2.063 2.333,2.26 0.156,0.198 10 true B 2.427,2.052 2.583,2.25 0.156,0.198 10 true B 2.25,1.354 2.406,1.552 0.156,0.198 10 true C 2.25,1.104 2.406,1.302 0.156,0.198 10 true C 1.958,2.323 2.115,2.521 0.156,0.198 10 true D 2.052,2.542 2.208,2.74 0.156,0.198 10 true D

i.

Check the difference in level "a" between the roof panel and the upper surface of the sliding roof glass sub-assembly when the sliding roof glass sub-assembly is fully closed.

HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.


Standard:
Area Measurement
A - A -1.0 to 3.0 mm (-0.0394 to 0.118 in.)
B - B -3.0 to 1.0 mm (-0.118 to 0.0394 in.)
C - C -1.0 to 3.0 mm (-0.0394 to 0.118 in.)
D - D -3.0 to 1.0 mm (-0.118 to 0.0394 in.)




c.
B565678C01
1.948,1.406 2.26,1.563 0.313,0.156 10 false *a
*a Even


Perform a gap check.

i.

Check the gap between the roof panel and sliding roof glass sub-assembly.

NOTICE:

The gap must be even all around.




d.

After adjusting the sliding roof glass sub-assembly, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 7.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218G 8.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Engage the 2 claws to install a new sliding roof side garnish LH.


Hide 63217G 9.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.