Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0421224 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B566183

Engage the 4 clamps to connect the airbag wire harness.


d.

Insert the 3 hooks and install the curtain shield airbag assembly with 5 new bolts, a new spacer, 8 new clips (A) with pins, and engage the 2 clips (B).

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.


HINT:

Engage the 2 claws to install each new clip (A).


B566185C01
5.135,2.146 5.385,2.146 true 5.896,2.063 6.146,2.063 true 3.156,2.229 3.385,2.458 3.385,2.458 3.594,2.458 true 6.667,0.354 6.438,0.354 6.438,0.354 6.438,1.104 true 5.406,2.073 5.615,2.25 0.208,0.177 10 false *1 6.167,1.99 6.375,2.167 0.208,0.177 10 false *1 5.833,0.479 6.042,0.646 0.208,0.167 10 true *b 1.885,1.51 2.094,1.677 0.208,0.167 10 false *a 6.698,0.281 6.906,0.448 0.208,0.167 10 true *c 3.625,2.375 3.833,2.552 0.208,0.177 10 false *2 4.146,0.854 4.354,1.021 0.208,0.167 10 true *b
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Spacer Location - -
V113147

Install in this Direction - -



e.

Using needle-nose pliers, push the 8 pins into the 8 clips (A).

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips (A) are pushed in firmly.




f.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

for A25A-FXS, A25B-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.INSTALL ROOF HEADLINING ASSEMBLY