Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY VOLTAGE SENSOR
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0419998 BATTERY VOLTAGE SENSOR A

HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of hybrid battery terminal block High voltage fuse accumulated load history reset DTCs are stored for 2WD:
(Click here)
for 4WD/AWD:
(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

The type of battery voltage sensor to be used varies depending on the vehicle model.

·

If the wrong type of battery voltage sensor is installed, the ignition switch cannot be turned on (READY).

·

When replacing the battery voltage sensor, always replace it with a new one.

·

After installing the battery voltage sensor, perform the following to check that the ignition switch can be turned on (READY).

-

Turn the ignition switch to on (READY).

-

Turn the ignition switch off and wait for 30 seconds or more.

-

Turn the ignition switch to on (READY) again.


·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide 82161 2.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A460097

Disconnect the electric vehicle battery plug assembly connector.


b.

Disengage the 3 clamps to disconnect the floor wire.


Hide G920Q 3.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide 4.REMOVE NO. 6 HV BATTERY CARRIER BRACKET

CAUTION:

Be sure to wear insulated gloves.


a.
A455838

Disengage the clamp.


b.

Remove the 4 nuts and No. 6 HV battery carrier bracket.


Hide 89892A 5.REMOVE BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves.


a.
A455839

Disconnect the 3 battery voltage sensor connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A455840

Remove the 2 nuts and battery voltage sensor from the HV battery.

NOTICE:

If the battery voltage sensor has been struck or dropped, replace it.