Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420014 PARKING ASSIST MONITOR SYSTEM J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E404537E11
0.083,1 1.385,1.396 1.302,0.396 10 false from IG1-NO. 1 Relay 2.031,1.229 2.823,1.531 0.792,0.302 10 false BKUP LP 4.5,0.854 4.688,1.042 0.188,0.188 10 false 2 3.271,0.865 3.458,1.052 0.188,0.188 10 false 1 3.021,1.24 3.375,1.427 0.354,0.188 10 false C52 3.01,1.458 4.781,1.844 1.771,0.385 10 false Park/Neutral Position Switch Assembly 5.135,0.854 5.344,1.063 0.208,0.208 10 false 28 5.427,0.969 5.833,1.177 0.406,0.208 10 false REV 5.177,1.583 5.583,1.792 0.406,0.208 10 false H1 5.167,1.76 6.875,2.104 1.708,0.344 10 false Radio and Display Receiver Assembly 3.448,0.906 3.854,1.115 0.406,0.208 10 false RB 4.177,0.885 4.583,1.094 0.406,0.208 10 false RL

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses and relays for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

Check that the "REV" item on the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Remove the park/neutral position switch assembly.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL


b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY AND BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY AND BATTERY)
a.

Disconnect the C52 park/neutral position switch assembly connector.


b.

Disconnect the H1 radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C52-1 (RB) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-2 (RL) - H1-28 (REV) Always Below 1 Ω
C52-2 (RL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR