Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420014 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


E286120N30
3.292,0.094 3.813,0.344 0.521,0.25 3.417,0.125 3.823,0.323 0.406,0.198 10 false W15

a.

Disconnect the W15 rear television camera assembly connector.


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
W15-6 (CB+) - Body ground Power source Ignition switch ACC 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the W15 rear television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
W15-3 (CV+) - W15-2 (CV-) Video signal Ignition switch ON
Shift position in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Ignition switch ON
Shift position in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
W15-5 (CGND) - Body ground Camera ground Always Below 1 Ω

If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying image)
*b Waveform 2 (camera lens is covered, blacking out screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal W15-3 (CV+) - W15-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens not covered, displaying image

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal W15-3 (CV+) - W15-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens covered, blacking out screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.