Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420015 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (master) judges that there is a communication problem with the blind spot monitor sensor RH (slave).

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor (master) cannot receive signals from the blind spot monitor sensor (slave)
·

Open or short in CAN bus main wire or connector

·

Open or short in No. 22 CAN junction connector

·

Blind spot monitor sensor RH (slave)

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor LH (master)



WIRING DIAGRAM

E439030E01
5.729,2.438 6.156,2.667 0.427,0.229 10 false M43 2.448,2.469 2.76,2.667 0.313,0.198 10 false M2 1.354,1.177 2.427,1.396 1.073,0.219 10 false ECU-IG1 NO. 3 5.729,2.594 6.958,3.135 1.229,0.542 10 false Blind Spot Monitor Sensor LH (Master) 4.021,2.625 5.333,3.052 1.313,0.427 10 false No. 22 CAN Junction Connector 4.031,2.469 5.24,2.875 1.208,0.406 10 false M34 5.073,1.844 5.365,2.281 0.292,0.438 10 false 13 4.01,1.833 4.302,2.271 0.292,0.438 10 false 12 4.073,0.979 4.365,1.417 0.292,0.438 10 false 1 5.094,0.979 5.385,1.417 0.292,0.438 10 false 2 2.531,2.063 3.104,2.313 0.573,0.25 10 false BRGD 2.344,0.906 2.635,1.344 0.292,0.438 10 false 5 2.271,1.969 2.563,2.406 0.292,0.438 10 false 10 2.531,1.01 3.104,1.26 0.573,0.25 10 false BRB 3.063,0.979 3.635,1.229 0.573,0.25 10 false CA2P 3.104,1.833 3.677,2.083 0.573,0.25 10 false CA2N 3.563,0.969 3.854,1.406 0.292,0.438 10 false 1 3.552,1.844 3.844,2.281 0.292,0.438 10 false 6 5.698,0.969 5.99,1.406 0.292,0.438 10 false 1 5.698,1.844 5.99,2.281 0.292,0.438 10 false 6 5.896,0.979 6.469,1.229 0.573,0.25 10 false CA2P 5.885,1.854 6.458,2.104 0.573,0.25 10 false CA2N 2.448,2.635 3.615,3.073 1.167,0.438 10 false Blind Spot Monitor Sensor RH (Slave) 0.135,1 1.083,1.542 0.948,0.542 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ TOYOTA Parking Assist-Sensor System A
w/o TOYOTA Parking Assist-Sensor System B



A

2.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)

B

3.CHECK CAN BUS MAIN WIRE
2.CHECK DTC OUTPUT (PARKING SUPPORT BRAKE SYSTEM)
a.

Using the GTS, check for DTCs according to the prompts on the screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Clearance Warning > Trouble Codes
50001 438
Standard:

The clearance warning ECU assembly does not output DTCs U117787 and U117887 simultaneously.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN BUS MAIN WIRE

NG

GO TO PARKING SUPPORT BRAKE SYSTEM (DTC U117787)

3.CHECK CAN BUS MAIN WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E334331C36
1.5,2.833 2,3.083 0.5,0.25 0.167,1.5 0.667,1.75 0.5,0.25 2.615,2.385 2.396,1.896 true 2.906,1.365 2.438,1.615 true 1,3.083 1.604,3.448 true 2.385,3.99 2.667,4.25 true 0.24,2.708 0.552,2.865 0.313,0.156 10 false *1 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.615,2.875 2,3.052 0.385,0.177 10 false H56 0.292,1.542 0.604,1.74 0.313,0.198 10 false M34 2.958,1.281 3.427,1.51 0.469,0.229 10 false CANH 2.51,2.427 3.094,2.635 0.583,0.208 10 false CANL 2.677,4.281 3.26,4.49 0.583,0.208 10 false BAT 0.74,2.969 1.323,3.177 0.583,0.208 10 false CG
*1 DLC3
*a Component with harness connected
(No. 22 CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M34-1 (CANH) - M34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M34-1 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M34-12 (CANL) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M34-1 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M34-12 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)

B

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 22 CAN JUNCTION CONNECTOR)

C

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)
a.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)
a.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


b.
C406586C09
1.417,0.25 1.917,0.5 0.5,0.25 2.458,0.729 1.948,1.031 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.573,0.292 1.885,0.49 0.313,0.198 10 false M2 2.552,0.615 2.958,0.813 0.406,0.198 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
M2-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DTC
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

OK:

No DTCs are output.


Result:
Proceed to
OK
NG



OK

NG

7.REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)
7.REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)

NEXT

8.RECHECK DTC
8.RECHECK DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 22 CAN JUNCTION CONNECTOR)
a.
E331799C66
1.417,0.25 1.917,0.5 0.5,0.25 0.958,1.844 1.24,0.927 true 0.646,1.854 0.333,1.052 true 1,2.781 0.906,2.177 true 0.406,2.938 0.677,2.177 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.542,0.292 2,0.49 0.458,0.198 10 false M34 0.104,0.875 0.719,1.073 0.615,0.198 10 false CANH*c 1.021,0.75 1.635,0.948 0.615,0.198 10 false CANH*b 0.198,2.969 0.813,3.167 0.615,0.198 10 false CANL*c 0.823,2.802 1.438,3 0.615,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (Master) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire


Disconnect the M34 No. 22 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-1 (CANH) - M34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M34-2 (CANH) - M34-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (master) CAN main wire) B
NG (to blind spot monitor sensor RH (slave) CAN main wire) C



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (MASTER))

C

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (SLAVE))
10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.
C406586C10
1.417,0.25 1.917,0.5 0.5,0.25 0.917,1.5 1.406,1.063 true 1.667,1.667 1.448,1.188 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.531,0.292 1.906,0.542 0.375,0.25 10 false M43 1.667,1.719 2.073,1.917 0.406,0.198 10 false CA2N 0.646,1.531 1.052,1.729 0.406,0.198 10 false CA2P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master))


Disconnect the M43 blind spot monitor sensor LH (master) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - M43-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - NO. 22 CAN JUNCTION CONNECTOR)

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.
C406586C11
1.417,0.25 1.917,0.5 0.5,0.25 0.917,1.5 1.406,1.063 true 1.667,1.667 1.448,1.188 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.969,0.542 0.406,0.25 10 false M2 1.667,1.719 2.073,1.917 0.406,0.198 10 false CA2N 0.646,1.531 1.052,1.729 0.406,0.198 10 false CA2P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Disconnect the M2 blind spot monitor sensor RH (slave) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) -M2-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - NO. 22 CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)
a.
E331799C67
1.417,0.25 1.917,0.5 0.5,0.25 0.958,1.854 1.271,0.906 true 0.635,1.854 0.313,1.063 true 1.198,2.771 0.906,2.167 true 0.323,2.792 0.677,2.167 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.542,0.292 2,0.49 0.458,0.198 10 false M34 0.083,0.875 0.698,1.073 0.615,0.198 10 false CANH*c 1.042,0.719 1.656,0.917 0.615,0.198 10 false CANH*b 0.115,2.823 0.729,3.021 0.615,0.198 10 false CANL*c 1.042,2.802 1.656,3 0.615,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (Master) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire


Disconnect the M34 No. 22 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (CANH) - M34-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M34-1 (CANH) - M34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (master) CAN main wire) B
NG (to blind spot monitor sensor RH (slave) CAN main wire) C



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

13.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))

C

14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
13.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.
C406586C10
1.417,0.25 1.917,0.5 0.5,0.25 0.917,1.5 1.406,1.063 true 1.667,1.667 1.448,1.188 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.531,0.292 1.906,0.542 0.375,0.25 10 false M43 1.667,1.719 2.073,1.917 0.406,0.198 10 false CA2N 0.646,1.531 1.052,1.729 0.406,0.198 10 false CA2P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master))


Disconnect the M43 blind spot monitor sensor LH (master) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - M43-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - NO. 22 CAN JUNCTION CONNECTOR)

14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.
C406586C11
1.417,0.25 1.917,0.5 0.5,0.25 0.917,1.5 1.406,1.063 true 1.667,1.667 1.448,1.188 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.969,0.542 0.406,0.25 10 false M2 1.667,1.719 2.073,1.917 0.406,0.198 10 false CA2N 0.646,1.531 1.052,1.729 0.406,0.198 10 false CA2P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Disconnect the M2 blind spot monitor sensor RH (slave) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) - M2-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - NO. 22 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)
a.

Disconnect the M34 No. 22 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C406587C03
4.083,1.417 4.583,1.667 0.5,0.25 1.833,0.25 2.333,0.5 0.5,0.25 1.385,1.49 0.99,0.813 true 1.625,1.49 1.771,0.75 true 1.177,2.313 1.427,1.74 true 1.885,2.271 1.594,1.74 true 6.104,0.771 5.771,1.188 true 6.49,1.781 6.656,2.281 true 0.188,0.104 0.5,0.302 0.313,0.198 10 false *a 4.479,0.115 4.792,0.313 0.313,0.198 10 false *1 6.625,2.302 7.083,2.5 0.458,0.198 10 false BAT 6.177,0.667 6.635,0.865 0.458,0.198 10 false CG 1.75,2.292 2.667,2.49 0.917,0.198 10 false CANL*b 1.542,0.583 2.458,0.781 0.917,0.198 10 false CANH*b 0.75,0.635 1.667,0.833 0.917,0.198 10 false CANH*c 0.979,2.333 1.896,2.531 0.917,0.198 10 false CANL*c 1.969,0.292 2.583,0.49 0.615,0.198 10 false M34 4.198,1.458 4.813,1.656 0.615,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (Master) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire - -


Standard Resistance:
Tester Connection Condition Specified Condition
M34-1 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-12 (CANL) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-1 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M34-12 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M34-2 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-13 (CANL) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-2 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M34-13 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (master) CAN main wire) B
NG (to blind spot monitor sensor RH (slave) CAN main wire) C



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))

C

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M43 blind spot monitor sensor LH (master) connector.


c.
E433084C03
1.417,0.25 1.917,0.5 0.5,0.25 1.5,1.833 2,2.083 0.5,0.25 0.917,0.833 1.396,1.052 true 0.917,1.417 1.365,1.229 true 1.625,2.354 1.083,2 true 2.5,3.083 2.292,2.844 true 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.615,1.875 2,2.083 0.385,0.208 10 false H56 1.531,0.292 1.958,0.542 0.427,0.25 10 false M43 0.5,0.74 1.115,0.938 0.615,0.198 10 false CA2P 0.5,1.385 1.115,1.583 0.615,0.198 10 false CA2N 2.51,3.135 3.125,3.333 0.615,0.198 10 false BAT 0.833,1.885 1.448,2.083 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M43-6 (CA2N) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M43-1 (CA2P) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M43-6 (CA2N) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - NO. 22 CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.

Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


c.
E433084C04
1.417,0.25 1.917,0.5 0.5,0.25 1.5,1.833 2,2.083 0.5,0.25 0.917,0.833 1.396,1.052 true 0.917,1.417 1.365,1.229 true 1.625,2.354 1.083,2 true 2.5,3.083 2.292,2.844 true 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.615,1.875 2,2.083 0.385,0.208 10 false H56 1.573,0.292 1.885,0.49 0.313,0.198 10 false M2 0.5,0.74 1.115,0.938 0.615,0.198 10 false CA2P 0.5,1.385 1.115,1.583 0.615,0.198 10 false CA2N 2.51,3.135 3.125,3.333 0.615,0.198 10 false BAT 0.833,1.885 1.448,2.083 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M2-6 (CA2N) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M2-1 (CA2P) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M2-6 (CA2N) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - NO. 22 CAN JUNCTION CONNECTOR)