Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420033 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Reverse Shift-linked Function of Power Mirrors does not Operate  


DESCRIPTION

The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Based on the signal, each outer mirror control ECU assembly then performs control.

WIRING DIAGRAM

B581838E03
0.104,5.448 2.51,6.094 2.406,0.646 10 false Hybrid Vehicle Control ECU*1 1.365,1.521 3.323,2.125 1.958,0.604 10 false Outer Mirror Switch Assembly 0.125,2.552 1.771,3.021 1.646,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 2.792,2.417 4.354,3.031 1.563,0.615 10 false Outer Mirror Control ECU Assembly (Driver Door) 4.604,5.406 6.656,6.031 2.052,0.625 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 2.75,5.396 3.865,5.75 1.115,0.354 10 false z16 2.74,5.563 4.302,6.146 1.563,0.583 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 4.646,2.385 6.698,2.865 2.052,0.479 10 false Outer Rear View Mirror Assembly (Driver Door) 4,3.615 4.458,3.813 0.458,0.198 10 false MV 4.01,4.208 4.469,4.406 0.458,0.198 10 false M+ 4,0.583 4.458,0.781 0.458,0.198 10 false MV 4.021,1.177 4.479,1.375 0.458,0.198 10 false M+ 4.344,0.448 4.802,0.646 0.458,0.198 11 false 1 4.344,3.51 4.802,3.708 0.458,0.198 10 false 1 4.333,4.104 4.792,4.302 0.458,0.198 10 false 10 4.323,1.063 4.781,1.26 0.458,0.198 10 false 10 5.188,0.813 6.698,1.052 1.51,0.24 10 false Vertical Mirror Motor 5.198,3.833 6.542,4.115 1.344,0.281 10 false Vertical Mirror Motor 0.563,6.448 2.646,6.688 2.083,0.24 10 false : CAN Communication Line 2.792,2.229 3.906,2.583 1.115,0.354 10 false z17 5.51,6.083 6.938,6.385 1.427,0.302 10 false *1: for HV Model 1.375,1.375 1.833,1.573 0.458,0.198 10 false J22 1.823,0.333 2.281,0.531 0.458,0.198 10 false M+ 1.813,0.719 2.271,0.917 0.458,0.198 10 false MSW 1.823,1.125 1.979,1.323 0.156,0.198 10 false E 0.646,0.323 1.26,0.521 0.615,0.198 10 false MIRB 0.646,0.729 1.26,0.927 0.615,0.198 10 false MIRS 0.646,1.104 1.26,1.302 0.615,0.198 10 false MIRE 0.115,5.865 0.885,6.063 0.771,0.198 10 false ECM*2 5.521,6.438 7.073,6.75 1.552,0.313 10 false *2: for Gasoline Model 0.125,2.385 0.583,2.583 0.458,0.198 10 false H44 1.094,0.24 1.573,0.802 0.479,0.563 10 false 7 1.094,1.01 1.25,1.208 0.156,0.198 10 false 9 1.094,0.625 1.427,1.25 0.333,0.625 10 false 8 1.625,0.229 1.781,0.427 0.156,0.198 10 false 4 1.625,0.615 1.781,0.813 0.156,0.198 10 false 5 1.625,1 2.104,1.563 0.479,0.563 10 false 7 4.76,1.792 6.708,2.375 1.948,0.583 10 false Outer Mirror Actuator Assembly (Driver Door) 4.792,4.854 6.74,5.5 1.948,0.646 10 false Outer Mirror Actuator Assembly (Front Passenger Door) 4.646,0.448 5.104,0.646 0.458,0.198 11 false 1 4.656,1.052 5.115,1.25 0.458,0.198 10 false 4 4.76,1.635 5.219,1.833 0.458,0.198 10 false B 4.656,3.51 5.115,3.708 0.458,0.198 11 false 1 4.667,4.104 5.125,4.302 0.458,0.198 10 false 4 4.781,4.688 5.24,4.885 0.458,0.198 10 false C

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION
a.

Check the electrical remote control mirror function operates normally.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Power electrical remote control mirror function operates normally.



Result:
Result Proceed to
Electrical remote control mirror function is normal A
Driver door electrical remote control mirror function is not normal B
Front passenger door electrical remote control mirror function is not normal C



A

2.CHECK MEMORY AND REACTIVATION FUNCTION

B

GO TO OTHER DIAGNOSTIC PROCEDURE (Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch)

C

GO TO OTHER DIAGNOSTIC PROCEDURE (Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch)

2.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions are normal A
Memory function is not normal B
Reactivation function is not normal C



A

3.CHECK FOR DTC

B

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror Surface Position is not Memorized)

C

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirrors do not Return to Memorized Position)

3.CHECK FOR DTC
a.

Check if hybrid control system DTCs are output.*

*: for HV Model


Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Check if SFI system DTCs are output.*

*: for Gasoline Model


Powertrain > Engine > Trouble Codes
50001 234
OK:

SFI system DTCs are not output.



Result:
Result Proceed to
OK A
NG (for HV Model) B
NG (for Gasoline Model) C



A

4.CHECK COMBINATION METER ASSEMBLY

B

C

4.CHECK COMBINATION METER ASSEMBLY
a.

Check if the shift position indicator light in the combination meter assembly operates normally.

OK:

Shift position indicator light indicates the actual shift position correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK REVERSE SHIFT-LINKED FUNCTION

NG

5.CHECK REVERSE SHIFT-LINKED FUNCTION
a.
B294057C03
0.177,0.115 0.49,0.313 0.313,0.198 10 false *a
*a Turns Downward


Turn the ignition switch to ON.


b.

Turn the mirror select switch R or L switch on.


c.

Check that the mirror surface turns downward when the shift lever is moved to R.


Result:
Result Proceed to
Reverse shift-linked functions on both mirrors are not normal A
Reverse shift-linked function on driver door is not normal B
Reverse shift-linked function on front passenger door is not normal C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

C

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)