Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420033 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror Surface Position is not Memorized  


DESCRIPTION

If the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. On receiving the seat memory switch signal, the main body ECU (multiplex network body ECU) sends the memory request signal to each outer mirror control ECU assembly via CAN communication. When receiving this signal, each outer mirror control ECU assembly stores the mirror surface position based on information from the mirror position sensor, which is built into the outer mirror actuator assembly.

WIRING DIAGRAM

B581837E02
3.281,0.333 3.896,0.531 0.615,0.198 10 false VSRL 3.438,0.813 3.75,1.01 0.313,0.198 10 false VC 3.302,1.313 3.917,1.51 0.615,0.198 10 false HSRL 3.469,1.792 3.781,1.99 0.313,0.198 10 false E1 3.448,4.094 3.76,4.292 0.313,0.198 10 false M1 3.458,4.656 3.771,4.854 0.313,0.198 10 false M2 3.417,5.167 3.729,5.365 0.313,0.198 10 false MM 5.385,5.042 6,5.24 0.615,0.198 10 false MMRY 5.385,4.573 5.542,4.771 0.156,0.198 10 false 2 5.375,4.021 5.531,4.219 0.156,0.198 10 false 1 5.188,4.021 5.344,4.219 0.156,0.198 10 false 3 5.167,4.583 5.323,4.781 0.156,0.198 10 false 4 5.167,5.042 5.323,5.24 0.156,0.198 10 false 2 3.896,0.156 4.052,0.354 0.156,0.198 10 false 6 3.906,0.635 4.063,0.833 0.156,0.198 10 false 5 3.854,1.104 4.167,1.302 0.313,0.198 10 false 13 3.865,1.594 4.177,1.792 0.313,0.198 10 false 14 4.75,0.271 4.906,0.469 0.156,0.198 10 false 2 4.76,0.729 4.917,0.927 0.156,0.198 10 false 3 4.76,1.167 4.917,1.365 0.156,0.198 10 false 1 4.792,1.667 4.948,1.865 0.156,0.198 10 false 4 3.281,6.521 3.896,6.719 0.615,0.198 10 false VSSR 3.448,6.969 3.76,7.167 0.313,0.198 10 false VC 3.271,7.469 3.885,7.667 0.615,0.198 10 false HSSR 3.49,7.917 3.802,8.115 0.313,0.198 10 false E1 3.802,6.417 3.958,6.615 0.156,0.198 10 false 6 3.813,6.875 3.969,7.073 0.156,0.198 10 false 5 3.792,7.385 4.104,7.583 0.313,0.198 10 false 13 3.802,7.823 4.115,8.021 0.313,0.198 10 false 14 4.708,6.417 4.865,6.615 0.156,0.198 10 false 2 4.708,6.875 4.865,7.073 0.156,0.198 10 false 3 4.719,7.344 4.875,7.542 0.156,0.198 10 false 1 4.729,7.802 4.885,8 0.156,0.198 10 false 4 3.885,3.906 4.042,4.104 0.156,0.198 10 false 2 3.885,4.469 4.042,4.667 0.156,0.198 10 false 3 3.885,4.938 4.042,5.135 0.156,0.198 10 false 1 0.469,9.385 4.135,9.583 3.667,0.198 10 false : CAN Communication Line 2.448,9.021 2.906,9.219 0.458,0.198 10 false z16 3.813,0.354 4.271,0.552 0.458,0.198 10 false z17 3.833,0.833 4.292,1.031 0.458,0.198 10 false z17 3.833,1.333 4.292,1.531 0.458,0.198 10 false z17 3.823,1.792 4.281,1.99 0.458,0.198 10 false z17 3.833,4.125 4.292,4.323 0.458,0.198 10 false J23 3.833,4.688 4.292,4.885 0.458,0.198 10 false J23 3.833,5.167 4.292,5.365 0.458,0.198 10 false J23 6.479,5.063 6.635,5.26 0.156,0.198 10 false E 6.656,5.063 6.813,5.26 0.156,0.198 10 false 1 4.969,2.063 5.271,2.281 0.302,0.219 10 false D 4.958,2.208 6.906,2.771 1.948,0.563 10 false Outer Mirror Actuator Assembly (Driver Door) 5.448,1.594 6.615,2.063 1.167,0.469 10 false Horizontal Sensor 5.781,0.604 6.813,1.021 1.031,0.417 10 false Vertical Sensor 4.063,2.99 6.969,3.49 2.906,0.5 10 false Outer Rear View Mirror Assembly (Driver Door) 5.333,5.479 5.792,5.677 0.458,0.198 10 false J21 5.333,5.656 6.698,6.177 1.365,0.521 10 false Seat Memory Switch 2.417,5.583 3.958,6.104 1.542,0.521 10 false Outer Mirror Control ECU Assembly (Driver Door) 0.073,5.479 1.719,6.323 1.646,0.844 10 false Main Body ECU (Multiplex Network Body ECU) 2.448,9.219 4.625,9.625 2.177,0.406 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 4.906,8.25 5.063,8.448 0.156,0.198 10 false E 4.906,9.229 6.958,9.844 2.052,0.615 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 4.885,8.427 6.833,9.115 1.948,0.688 10 false Outer Mirror Actuator Assembly (Front Passenger Door) 5.865,6.771 6.938,7.177 1.073,0.406 10 false Vertical Sensor 5.458,7.729 6.656,8.115 1.198,0.385 10 false Horizontal Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The mirror surface position will not be memorized if the ignition switch is not ON.

·

The mirror surface position will not be stored if the seat memory SET switch and 2 or more seat memory switches are pressed simultaneously.

·

If the operation fails, the mirror surface position will not be memorized until the seat memory SET switch is released and the operation is attempted again.

·

The mirror surface position will not be memorized when the mirror is operated manually.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




HINT:

Each outer rear view mirror assembly has a built-in mirror vertical position sensor and mirror horizontal position sensor.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-
Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 225 1,2,4
Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-
Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 224 1,2,4
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT MEMORY SWITCH (SEAT POSITION MEMORY FUNCTION)

NG

10.INSPECT SEAT MEMORY SWITCH
2.CHECK SEAT MEMORY SWITCH (SEAT POSITION MEMORY FUNCTION)
a.

When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

3.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

3.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on driver door mirror are not normal B
Memory and reactivation functions on front passenger door mirror are not normal C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (WIRE HARNESS)

C

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (WIRE HARNESS)
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (WIRE HARNESS)
a.

Remove the outer mirror actuator assembly (driver door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Disconnect the z17 outer mirror control ECU assembly (driver door) connector.


c.
B559030C18
0.167,2.917 0.542,3.115 0.375,0.198 0.156,0.635 0.531,0.833 0.375,0.198 1.573,0.135 1.781,0.135 1.781,0.135 1.781,0.708 true 2.125,1.24 1.938,1.24 1.938,1.24 1.938,0.99 true 1.781,1 1.781,1.24 1.781,1.24 1.615,1.24 true 1.948,0.708 1.948,0.146 1.948,0.146 2.125,0.146 true 0.302,2.927 0.521,3.094 0.219,0.167 10 false D 0.24,0.656 0.573,0.823 0.333,0.167 10 false z17 0.25,0.396 0.563,0.594 0.313,0.198 10 false *a 0.271,2.698 0.583,2.896 0.313,0.198 10 false *b 1.323,0.063 1.656,0.229 0.333,0.167 10 false VC 2.188,1.156 2.521,1.323 0.333,0.167 10 false E1 1.177,1.167 2.031,1.448 0.854,0.281 10 false HSRL 2.198,0.073 2.813,0.271 0.615,0.198 10 false VSRL
*a Front view of wire harness connector(to Outer Mirror Control ECU Assembly (Driver Door))
*b Front view of wire harness connector(to Outer Mirror Actuator Assembly (Driver Door))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z17-6 (VSRL) - D-2 Always Below 1 Ω
z17-6 (VSRL) or D-2 - Body ground Always 10 kΩ or higher
z17-5 (VC) - D-3 Always Below 1 Ω
z17-5 (VC) or D-3 - Body ground Always 10 kΩ or higher
z17-13 (HSRL) - D-1 Always Below 1 Ω
z17-13 (HSRL) or D-1 - Body ground Always 10 kΩ or higher
z17-14 (E1) - D-4 Always Below 1 Ω
z17-14 (E1) - D-4 Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

5.REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR)
a.

Temporarily replace the outer mirror actuator assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY AND REACTIVATION FUNCTION
6.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR ACTUATOR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (WIRE HARNESS)
a.

Remove the outer mirror actuator assembly (front passenger door).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Disconnect the z16 outer mirror control ECU assembly (front passenger door) connector.


c.
B559030C19
0.167,2.917 0.542,3.115 0.375,0.198 0.156,0.635 0.531,0.833 0.375,0.198 1.573,0.135 1.781,0.135 1.781,0.135 1.781,0.708 true 2.125,1.24 1.938,1.24 1.938,1.24 1.938,0.99 true 1.781,1 1.781,1.24 1.781,1.24 1.615,1.24 true 1.948,0.708 1.948,0.146 1.948,0.146 2.125,0.146 true 0.302,2.927 0.521,3.094 0.219,0.167 10 false E 0.24,0.656 0.573,0.823 0.333,0.167 10 false z16 0.25,0.396 0.563,0.594 0.313,0.198 10 false *a 0.271,2.698 0.583,2.896 0.313,0.198 10 false *b 1.323,0.063 1.656,0.229 0.333,0.167 10 false VC 2.188,1.156 2.521,1.323 0.333,0.167 10 false E1 1.177,1.167 2.031,1.448 0.854,0.281 10 false HSSR 2.198,0.073 2.813,0.271 0.615,0.198 10 false VSSR
*a Front view of wire harness connector(to Outer Mirror Control ECU Assembly (Front Passenger Door))
*b Front view of wire harness connector(to Outer Mirror Actuator Assembly (Front Passenger Door))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-6 (VSSR) - E-2 Always Below 1 Ω
z16-6 (VSSR) or E-2 - Body ground Always 10 kΩ or higher
z16-5 (VC) - E-3 Always Below 1 Ω
z16-5 (VC) or E-3 - Body ground Always 10 kΩ or higher
z16-13 (HSSR) - E-1 Always Below 1 Ω
z16-13 (HSSR) or E-1 - Body ground Always 10 kΩ or higher
z16-14 (E1) - E-4 Always Below 1 Ω
z16-14 (E1) or D-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

8.REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)

8.REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR)
a.

Temporarily replace the outer mirror actuator assembly (front passenger door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY AND REACTIVATION FUNCTION
9.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C13
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

10.INSPECT SEAT MEMORY SWITCH

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) AND BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH

11.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) AND BODY GROUND)
a.

Disconnect the J23 outer mirror control ECU assembly (driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J21-2 (MMRY) - J23-1 (MM) Always Below 1 Ω
J21-3 (1) - J23-2 (M1) Always Below 1 Ω
J21-4 (2) - J23-3 (M2) Always Below 1 Ω
J21-1 (E) - Body ground Always Below 1 Ω
J21-2 (MMRY) or J23-1 (MM) - Body ground Always 10 kΩ or higher
J21-3 (1) or J23-2 (M1) - Body ground Always 10 kΩ or higher
J21-4 (2) or J23-3 (M2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR